2 Watts 5 Watts 10 Watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
$450.00 – $980.00
2 Watts ose 5 Watts ose 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
Kjo është një pjesë kryesore e një transmetuesi video pa tel, të cilat mund të zmadhojnë sinjalin RF për një rreze dhe distancë më të madhe. fakultativ 1 vat, 2 vat, 5 vat, dhe 10 vat.
Tabela e Përmbajtjes
karakteristika
- Brezi i frekuencës: 800Mhz-830 Mhz, 1425MHz-1455MH
- RF në: 25± 2dBm
- RF jashtë fuqisë: 2 vat (33dBm)
- 1400Mhz Transmitter gains 11dB when used with një modul lidhjesh të dhënash video me valë me dy drejtime, konfiguroni fuqinë maksimale RF si 22~24 dBm, then the RF out power will be 33~35 dBm.
- 800Fitimi i transmetuesit Mhz: 13dB, when used with a two-way wireless video data link module, konfiguroni fuqinë maksimale RF si 20~22 dBm, then the RF out power will be 33~35 dBm.
- RF jashtë fuqisë: 5 vat (37dBm)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~25 dBm, then the RF out power will be 37~37 dBm.
- 800Fitimi i transmetuesit Mhz: 17dB, when used with a two-way wireless video data link module, konfiguroni fuqinë maksimale RF si 20~22 dBm, then the RF out power will be 37~39 dBm.
- RF jashtë fuqisë: 10 vat (40dBm)
- TX fitim: 18dB, when used with a two-way wireless video data link module, set up the maximum RF power of as 22~24 dBm, then the RF out power will be 40~42dbm.
- 2 Watts Power in DC12V~16V;
- 5 Watts Power in DC24V~25V, minimum 1.8A@24V power current rating
- 10 Watts Power in DC24V~30V, minimum 2.5A@28V power current rating
- 2 Watts Power consumption: <6W mesatare; 5 Watts Power consumption: <14W mesatare; 10 Watts Power consumption: <28W mesatare
- 2 Watts 5 Watts PCBA size: 46.5*31mm, trashësia e PCB: 1.2mm
- 10 Watts Dimensions: 65*62*13.5mm, not including the connector out of the metal housing, peshë: 98g
- rezistencë e plotë: 50 om
Duke punuar së bashku me një modul lidhjesh të dhënash video me valë me dy drejtime:
RF Input
Prodhimi RF
| Transmetues video me valë SDI për transmetuesin e lidhjes zbritëse COFDM me rreze të gjatë kamerash | We should solder two bonding pads to connect with power VDD and GND. |
| kontroll | We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL dhe GND). Inputi i lartë (1.8V deri në 3.3 V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode. |
| RF në | Konektor IPEX për lidhje me antenën kryesore të modulit të lidhjes së të dhënave video me valë me dy drejtime. |
| RF jashtë | We should solder the bonding pad to an antenna connector. |
Housing case and assemble
We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.
To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.
It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.
Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.
We can also make a metal chamber for this PA module according to the customer’s requirement.
The below model has a built-in Power Amplifier inside.
FAQ:
Q: Could you tell me your RF power amplifier dimension size? I want to design my enclosure.
A: Ju lutemi kontrolloni foton e mëposhtme. And tell us if you need any further information.
Q: Could you show me the real photos of your RF linear power amplifier?
A: me siguri, please check the below pictures.
Q: Are you not using the TQP7M9104 amplifier in the 2W module?
A: jo
