OSD ڊسپلي فنڪشن COFDM وصول ڪندڙ تي

Key1: turn on/off the status of the OSD displaying, سوئچ ڪرڻ لاءِ ان کي ڊگھو دٻايو(1s کان وڌيڪ). the status will be kept after reboot. جڏهن او ايس ڊي اسٽيٽس تي آهي بغير ڪنهن به او ايس ڊي ڊيٽا ان پٽ جي ڊيٽا uart کان, ڊوائيس وڊيو اسڪرين تي معلومات ڏيکاريندو جيئن:

عمير علي：338.0MHz ابن：4.0MHz; عمير علي, ڪم ات; ابن, رفتار

QPSK CR：2/3 GI:1/16; النجوم, رٿا, نگهبان interval.

شالي：3.90Mbps; شالي, وائرليس منتقلي bitrates

VBR：3.05Mbps AES بند; VBR, وڊيو bitrates; AES بند, AES انڪرپشن بند ڪيو ويو.

SIG1：27 SIG2：22; SIG1, signal intensity of ant 1; SIG2, signal intensity of ant 2

ber1:0.14% ber2:100.00%; ber1, bit error rate of ant 1; ber2, bit error rate of ant 2

بند REC نه رکڻ جي; وڊيو رڪارڊنگ جي صورتحال

What is VBR? VBR is the video encoding bit rate at the transmitter. Since the video picture changes dynamically, VBR is of course variable, but it fluctuates around the encoding bit rate set by the transmission system: 7.81*0.8=6.248Mbps

How to use OSD API in Our COFDM systems?

Steps description:

1) The customer’s module sends the digital data to our COFDM transmitter via UART;

2) Our transmitter will send the digital data with video data together to our COFDM receiver via the wireless link;

3) Our receiver will send out the digital data to the customer’s module via UART;

4) The customer’s module should transfer the digital data into the characters string they want to show on the video screen in OSD mode. Then the customer’s module sends the characters string to our receiver via the same UART.

5) Our receiver will display the character’s string on the HDMI display screen with the video together in OSD mode.

API of Our COFDM receiver:

command	ATOSD$(font), $(x),$(y),$(str) _مثال：ATOSD1,40,20,height: 100m_
parameters	font: 0: 8×16, جا جزا; 1: 16×24, جا جزا; x: 0 جي طرف 1919, horizontal axis; ۽: 0 جي طرف 1079, vertical axis; Str: characters string start to show on the HDMI screen from (x,y) point; space characters used for a clean screen at that point. Since ’_’ is the command end flag, No ’_’ can be used in these parameters.
فعل	To display the characters string on the HDMI screen with the video in OSD mode
return	Null
وضاحت	1) This command is used for the customer’s MCU module to our Receiver via data UART; 2) You can use اي ٽي ايس ٽي command(described in other documents) to define our Receiver UART; 3) You should draw the HDMI screen following 1920*1080 pixels via (x,y) axis. Our receiver firmware will adjust it automatically according to the real screen systems.