HD Yonyamula COFDM Mobile Video Wireless System Users Manual

COFDM Mobile Video Wireless Transmission users manual for COFDM-908T and COFDM-912T

Users Manual for COFDM Mobile Video Wireless Transmission

This is a manual for COFDM-912T and COFDM-908T. If the HD input is mentioned in the text, it refers to the COFDM-908T model. If the SD input is mentioned in the text, it refers to the COFDM-912T model. Please Pay attention to the distinction.

1. Mawonekedwe

  • kwambiri Integrated, kamangidwe yodziyimira payokha
  • Adopt COFDM modulation technology, H.264 ukadaulo wolemba zithunzi
  • Can transmit one 1080P HDMI signal and one unidirectional data up to 230400Kbps
  • Low kachedwedwe, the minimum end-to-end latency is 350ms
  • Onse chonse kulankhulana, musawope kumanga mpanda
  • High-speed travel-to-travel communication,
  • Kutumiza koziziritsira kozungulirapo kotayikira, shockproof ndi mphamvu zosagwira
  • Non-mzere wa m'maso (NLOS) Kutumiza kwa mafoni, the transmission distance of 2W power is not less than 30 kilometers under the condition of no interference, the transmission distance of 5W power is not less than 50 makilomita, and the transmission distance of 10W power is not less than 80 makilomita
  • Liwiro loyenda kwambiri limatha kufika ku 600Km / ola limodzi (kuyeza)
  • Kulandila kwama synchronous kwa ma audio ndi makanema, Kutanthauzira kwamtundu wa HDMI1080P mitundu ingapo mwasankha, kutanthauzira koyenera kwamtundu wazithunzi za DVD
  • Wolandirayo amatha kuzindikira kujambula kwamavidiyo ndi ntchito zosunga zobwezeretsera
  • 128-pang'ono kubisa kwa AES ndi kufotokozera
  • Can provide full customization

2. ntchito

This product is mainly used in technical reconnaissance and evidence collection of public security and safety inspection departments, real-time picture transmission of drones and unmanned ships, radio and television broadcasting, broadcasting live broadcasting: wailesi ya munda, kuwulutsa zamasewera, uthenga chikhalidwemlengalenga moyo、situdiyo, mountaineering expeditions and more. Ndioyenera kutumiza kwanthawi yayitali kwazithunzi zapamwamba m'malo osiyanasiyana ovuta monga madera akumidzi, nyanja, ndi mapiri.

3: Parameter Indicators

1: chopatsilira (only standardized pictures, except for customization)

1 Watts PA transmitter
5 Watts PA Transmitter
10 Watts 20 Watts PA transmitter

Product parameters:

KusinthasinthaCOFDM
opaleshoni VotejiDC11V~DC17V
ntchito panopa1W:≤1.3A DC12V,5W:≤2.5A DC12V,10W:≤5.2A DC12V
mawonekedwe owongoleraStandard RS232 interface, 8 deta Akamva, 1 amasiya pang'ono, ngakhale parity, mlingo baud: 19200
mawonekedwe owonekeraNjira imodzi transparent siriyo doko kufala, 8 deta Akamva, 1 amasiya pang'ono, kuthandiza wosamvetseka parity, ngakhale parity, parity opanda zingwe, mlingo baud: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 、230400
kubisaThandizani kubisa kwa 128-bit
kusinthasintha mapangidweQPSK(4QAM)、16QAM、64QAM
patsogolo zolakwa kudzudzulidwa1/2 2/3 3/4 5/6 7/8
alonda imeneyi1/32 1/16 1/8 1/4
Chiwerengero cha onyamula2K
pafupipafupi bandiwifi2/3/4/5/6/7/8M chosinthika
mtsinje wamayendedwe2000kbs ~ 20000kbs chosinthika
zimafalitsa mphamvu1W/5W/10W
Kutumiza pafupipafupiAny frequency can be customized, the frequency is continuously adjustable, the adjustable range is ±20MHz, and the step is 1MHz
mphamvu flatnessLess than 0.2dB in 10MHz band
phewa chiŵerengeroThe shoulder-to-shoulder ratio is better than -28dB at full power output
second harmonic≤ -45dB
MORE32DB
kanema wowonjezera720×480 60I(NTSC), 720×576 50I(mnzako), 720 50P, 720 60P, 1080 50ine, 1080 60ine, 1080 24P, 1080 25P, 1080 30P, 1080 50P, mitundu yosiyanasiyana ndi kusintha.
HD mawonekedweHDMI
mtundu wobisalira wamavidiyoH.264
muyezo ProtectionZonse zotayidwa Redieta mtundu galimotoyo, odana ndi dzimbiri, kapangidwe kodzidzimutsa
Cacikulu kukula102*80*30mm(1w)/102*90*30mm(5W)/188*47*34mm(10W)/228*55*40mm(20W)
Kulemera Kwathunthu≤0.20KG (1W) / ≤0.27KG (5W) ≤1.5KG (10W) ≤2KG (20W)

2: wolandila

One Antenna or Two Antenna COFDM Receiver

Product parameters:

Portable multi-bandwidth HD receiver parameters
Landirani mafupipafupi170-860MHz VHF&UHF
pafupipafupi bandiwifi2/3/4/5/6/7/8MHz, optional
Mulingo woyikira wa RF-94dBm ~ -15dBm (pa 8M bandiwifi)/-98dBm ~ -15dBm (at 2M bandwidth)
RF athandizira impedance50 ohms
RF cholumikizira athandiziraN mutu
njira DemodulationCOFDM
Constellation wayQPSK, 16QAM, 64QAM (optional)
patsogolo zolakwa kudzudzulidwa1/2,2/3,3/4,5/6,7/8 (optional)
Chiwerengero cha onyamula2K,
alonda imeneyi1/32,1/16,1/8,1/4 (optional)
kutsitsa makanemaMPEG-2MP@ML/H.264
screen aspect ratio4:3 16:9
Video output image720*576@8MHz 1080P@60P、50P、50ine、30P、
mawonekedwe otulutsa mawuStereo unbalanced 300/ 200mv
linanena bungwe Audio2linanena bungwe Audio + 2linanena bungwe Video
opaleshoni VotejiAC220V/DC12V <0.4A
kutentha opaleshoni-20~ ~ + 50 ℃
physical dimension136*115*35mm non-standard all-aluminum shell
zida zolemera0.35Kg

4: Instructions for use

1: chopatsilira

  1. Functional area description

“ANT”: Transmitting antenna interface, please connect the antenna before powering on

“HDMI”: High-definition video input interface, input below 1080/50P

“Ctrl”: Transmitter tuner connection interface

“DC 12V”: DC12V power input port. “+” is the positive pole of the power supply, “-” is the negative pole of the power supply

“DC” is: Power indicator light, when the light is always on, it means that the power input of the transmitting module is normal

“TS”: Video input detection indicator light, this light is always on to indicate video input and normal encoding

  1. Parameter Configuration Description

Connect the transmitter parameter adjuster, press the “MENU/OK” key to enter the menu, the encryption key and data serial port parameters are displayed first, press the left or right key to move the cursor, and the up and down keys to adjust the parameters

After the parameter setting is completed, press “MENU/OK” to enter the next menu, and the interface is displayed as shown in the figure

Press the left or right key to move the cursor, press the up or down key to adjust the required parameters, the interface prompts as shown in the figure

After all parameter settings are completed, press the “MENU/OK” key to confirm, and the display will be as shown in the figure.

After the setting is completed, the parameters are written successfully, and the display is as shown in the figure

  1. General Troubleshooting

ndi: The light is off after the power is turned on: Check whether the power input meets the standard

b: “TS” indicator light is off: Check the video input connection cable, check whether the video input format conforms, and check whether the camera is interfered with (you can judge by holding the antenna with your hand).

C: The temperature of the transmitter is very low: check whether the current is normal (the deviation can be ±0.2A within the standard current).

D: Three lights are always on, and one of them is super bright: it means that the transmitter has failed the detection, and you can try to power off and restart (uncommon)

2: wolandila

  1. Functional area description

“RF in1” “RF in2”: receiving antenna interface, it is recommended to connect the antenna and then turn on the power switch, because the static electricity of the human body may cause the receiver to crash.

“HDMI”: Kanema linanena bungwe mawonekedwe, the output video format can be adjusted through the “HDMI” menu on the control panel.

“DC 12V”: mawonekedwe mphamvu athandizira, please strictly follow the power supply voltage requirements, and overvoltage input is strictly prohibited

“ON/OFF”: power switch.

“USB”: video storage interface, when the U disk is inserted, press the “EXIT” button to start the video recording, after the recording is successful, the video display will display the video recording time, and the stored file name is “TS”.

  1. LCD parameter description

ndi:CH01 UNLOCKED(LCKED)

“CH01” means the channel number of the receiver, “UNLOCKED” means the received signal is unlocked, and “LCKED” means the signal is locked. “CH00” of the receiver is the initial writing channel, and the default channel corresponding to the normal operation of the transmitter is “CH001”

b: FREQ:602.0MHz

“602.0MHz” is the receiving frequency of the receiver, this frequency must be consistent with the frequency set by the transmitter, otherwise the receiver will not search or receive the signal from the transmitter

m'ma: bw:6.0MHz

“BW” bandwidth, as shown in the figure, “BW: MHz” is understood as the RF bandwidth is 6MHz, this bandwidth must be consistent with the bandwidth set by the transmitter, otherwise the receiver will search for or cannot receive the signal from the transmitter

D: FEC:1/2

“FEC: 1/2” is the channel error correction, this parameter synchronizes the parameters set by the transmitter, and the receiver cannot be modified

imelo: GI:1/32

“GI:1/32” is the channel guard interval, this parameter is set by the transmitter synchronously, and the receiver cannot be modified

f:MAP: QPSK

“MAP: QPSK” is the modulation mapping, this parameter number is set by the transmitter synchronously, and the receiver cannot be modified

ga: SNR:0.0DB(SNR:15.0DB)

“SNR: 15.0dB” is the signal quality (kuti, the signal-to-noise ratio, the larger the value, the better). When “0.0dB” is displayed, the signal quality is 0, and the receiver will not be able to lock

"(SNR:15.0DB)” means the receiving signal-to-noise ratio is greater than 15dB. In the “QPSK” modulation mapping state, as long as the signal-to-noise ratio is greater than 6dB, the receiver can lock

H: PW:-72.1dBm(PW:-72.1)

PW is the received signal strength, (reference level value), the farther the transceiver end is relative to the distance, the weaker the signal strength is, and the larger the displayed value is, when the transmitter is not turned on, if the signal strength of the receiver is greater than -90dBm (such as -79.7dBm), it can be considered as adjacent frequency interference

  1. Parameter Configuration Description

Power on the receiver, and press the “MENU/OK” button to enter the menu, the first display is the menu of adjustable parameters, if you search for a specified frequency, directly press the “MENU/OK” button to enter the menu; if you want to remove the channel, press Press down to select “ListanbulChannel”, and then press “MENU/OK” to enter the menu operation; if you need to change the video output format, move the cursor to the “HDMI Mode” menu, press “MENU/OK” to enter, and select the video to be output After formatting, press the “MENU/OK” key to confirm.

The frequency search method is as follows. After entering the frequency setting menu, the interface is displayed as shown in the figure. Press the left or right key to move the cursor, press the up or down key to adjust the frequency, RF bandiwifi, and secret key that match the transmitter, and press the “MENU /OK” key to search. Note that the transmitter must be turned on at this time, mwinamwake, the receiver will not be able to lock because it cannot find the signal.

COFDM Mobile Video Wireless Transmission with a cheap price is including a transmitter and receiver for China directly

When the search is completed, press “MENU/OK” to confirm, and the channel is saved in the register of the assistant board, as shown in the figure. To save the channel to the receiver register, press the “MENU/OK” key and the right key at the same time.

After the receiver parameter setting is completed, the functions of the panel keys are as follows

"”“": each individually selectable receiver channel “CH**”

"”“": You can choose to view the hidden parameters of the receiver

“EXIT”: start and stop recording

  1. Video function

Insert the storage device into the “USB” interface of the receiver, press the “EXIT” button to start recording, and a blue recording time box will appear on the upper left corner of the video display as shown below

  1. General Troubleshooting

ndi: The value after the receiver displays “-” is very low (Tx is not turned on): It means that the current channel has serious electromagnetic interference, and the normal value is -90- -100.

b: Cannot record video: check the U disk or replace the U disk.

C: No signal received: Check whether the channel frequency is consistent with the transmitter.

D: No video output: Check the connection line, power off, and restart to check whether there is a boot interface.

Siyani Mumakonda

Imelo yanu sisindikizidwa. Minda yofunikira yalembedwa *

Discover more from iVcan.com

Lembetsani tsopano kuti mupitirizebe kuwerenga ndikupeza mwayi wosungira zonse.

Pitirizani kuwerenga

Amafuna Thandizo pa WhatsApp?
Exit mobile version