ड्रोन भिडियो डाटा लिङ्क UHF Vcan2024 को लागि IP जाल रेडियो ट्रान्सीभर मोड्युल

IP mesh radio transceiver module for drone video data link UHF

IP mesh radio transceiver module is suitable for point-to-multi-point or multi-point-to-multi-point network requirements.

जस्तै, your project requires multiple transmitters and multiple receivers. Each node can act as a relay for other nodes. Each node cannot be individually defined as a transmitter, रिसीभर, or repeater. Each node is a transmitter, a receiver, and a repeater. Such as security squads, bicycle racing, 2+ drones in the sky and 2+ receivers on the ground, and other applications.

सुविधा

1. Two-way bidirectional transmission video data download and upload
2. TDD OFDM full-duplex IP Mesh radio wireless transceiver module for video and data transmission
3. Dual RF Power: 24±1dBm, 2-च्यानल
4. Optional Working Frequency: 566~678MHz (112Mhz range hopping), 1420~1530MHz (110Mhz range hopping)
5. Three Ethernet RJ45 for video or data and One RS232 UART data link, UART नियन्त्रण (TTL) पोर्ट
6. Support transmit distance: 500~2000 meters (यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो), 5~22km (यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो); For a longer range, we needed the extra power amplifier support. (2वाट, 5वाट, 10वाट)
7. This board supports the CX6779K modem.

FHSS Frequency Hopping

• We designed this wireless video and data transmission with uplink and downlink for those who need the frequency automatic hopping function.
• With frequency hopping technology (यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो) to ensure better stable signal communication, when the current frequency signal is worse, the system will automatically change the working frequency to another frequency for a better signal.
• This bidirectional OFDM radio module can work from 566Mhz to 678MHz or from 1420Mhz to 1530MHz bandwidth. So the frequency range has 110Mhz bandwidth change or hopping. If you set the frequency bandwidth at 10 मेगाहर्ट्ज, then there are 11 frequency points for hopping.

विशिष्टता

• यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो (Need FDD COFDM model?)
• समर्थन 2 Frequency ranges (566~678MHz/1420~1530MHz)
• Supports FHSS frequency automatic hopping function
• 4/3/5/10/20/40यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो
• Max 100Mbps throughput
• Dual RF transmission power: 24±1dBm, 2-channel for uplink and downlink
• नक्षत्र: QPSK, 16QAM, 64QAM, यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो
• संवेदनशीलता: -95dBm (20मेगाहर्ट्ज ब्यान्डविथ)
• Supports IP Video Data Transmission (3 इथरनेट पोर्ट)
• यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो (1एक्स RS232, 1X TTL)
• Without extra PA, Up to 22km LOS (यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो) र 2km LOS(यो मोडेल दुई-तरिका वायरलेस डाटा लिङ्क संग भिडियो र डाटा वायरलेस प्रसारण लागि डिजाइन गरिएको थियो)
• Can add 2watts, 5वाट, वा 10 watts to support longer range
• Web UI and control UART for management
• AES128 एन्क्रिप्शन
• अपलिंक र डाउनलिङ्क स्ट्रिम नियन्त्रण (Video stream needs more and data streaming needs less)
• नेटवर्किंग मोड: One-to-one P2P, one-to-many P2MP, many-to-one MP2P, relay/repeater, mesh or swarm network。
• शक्ति खपत: <7डब्ल्यू
• आयाम: 80 एक्स 57 x 9.1mm
• वजन: 41G
• Working Temperate: -20℃ ~ +65 ℃
• Storage Temperate: -40℃ ~ +80 ℃

IP Radio Module Connector (इनपुट / उत्पादन)

• COFDM मोडुलेशन र H.264/H.265 भिडियो कम्प्रेसन	2PIN PH2.0mmConnector, DC in:9~30V
इथरनेट-1	4PIN PH1.25mm कनेक्टर
इथरनेट-2	4PIN PH1.25mm कनेक्टर
Ethernet-3	4PIN PH1.25mm कनेक्टर
डाटा UART	3PIN PH1.25mm कनेक्टर, RS232(or TTL 3.3V)
UART नियन्त्रण गर्नुहोस्	3PIN PH1.25mm कनेक्टर, टीटीएल ३.३ वी
USB	Micro USB Connector, for software upgrading
स्विच गर्नुहोस्	Tx/Rx control signal for outside power amplifier
Main-Antenna	Tx/Rx एन्टेना पोर्ट, IPEX
Second-Antenna	Tx/Rx एन्टेना पोर्ट, IPEX
12वि आउट	On-board 12V out(<200mA), for cool fan power supply

इथरनेट १, Ethernet2 and Ethernet3

The three Ethernet ports on board are bridged connections, so their IP addresses are the same. The photo below shows the 4PIN signals of the Ethernet port.

Switch Port

This port is a TX transmitter / RX receiver control signal for the extra power amplifier. The maximum RF transmission power of our module is 24±1dBm two channels, We also provide the correct power amplifier to increase the RF Power to 2-watt / 5-watt /10-watt if you need a longer range than 22km.

The below diagram shows how to add a power amplifier outside extra of this IP Radio Module.

This operation is for your reference only. If you need to add an external power amplifier, it is best to tell us and we will configure it for you, or ask a professional to operate it, अन्यथा, the PA will be easily burned.

संकेत	Electrical level	I/O	विवरण	mark
PA-enable1	1.8वी	को	High electrical level: data transmitting, change to high electrical level at 3.19us before transmitting and to low electrical level at 0.26us after transmitting finished.	High-Tx Low-Rx

डाटा UART

• The data UART is RS232 as default.
• We also can change the data port from RS232 to TTL 3.3V UART before the cargo delivery.
• The baud rate of data UART can be set as 115200, 57600, 38400, 19200, 9600, 4800, 2400, र 1200.

  

   

Control UART and USB port

Only one of these two ports is valid at the same time. Control UART is valid by default shipment. Please contact us if you need to use a USB UART. You can manage our module with Web UI or AT command via control UART.

LEDs light

LED1: शक्ति एलईडी, रातो, light on normal powered.

LED2: blue, LED3: हरियो, LED2 and LED3 indicate the wireless working status as described in the below table.

केन्द्रीय नोड	Blue LED2 light on all the time and green LED3 is not light
Access node	Green LED3 light on all the time when the access node is connected with the central node.
	The blue LED2 indicate the access node linking signal status with the central node. When the wireless linking signal is strong, blue LED2 blinks every 30 सेकेन्ड; When the wireless linking signal is middle, blue LED2 blinks every 6 सेकेन्ड; When the wireless linking signal is weak, blue LED2 blinks every 1 दोस्रो.

Sometimes customers may need to assemble the indicating LEDs on their housing case panel, so our board also provides a soldering hole for the three LED signals. The LED signal is described in the below table.

लिड	विवरण	Representation soldering hole
LED1	शक्ति एलईडी	LED1-GND and LEDs-VCC
LED2	Wireless indicating LED	LED2-GND and LEDs-VCC
LED3		LED3-GND and LEDs-VCC

Wireless networking with the IP MESH Radio Module

• Our module supports two operating modes: SMA महिला. It can be managed through Web UI or AT command via control UART.
• Our module supports features of a maximum of 63 SMA महिला. All the Nodes are in the same wireless LAN and share the whole transmission bandwidth (maximum 100Mbps throughout).
• Data from the Central Node to the Access Node, SMA महिला, and data from the Access Node to the Central Node, SMA महिला.
• Uplink and downlink stream ratio can be controlled through web UI or AT command.
• When using Our module for Point-to-Point transmitting, अपलिंक र डाउनलिङ्क स्ट्रिम अनुपात वेब UI वा नियन्त्रण uart मार्फत नियन्त्रण गर्न सकिन्छ (maximum 100Mbps throughout) अपलिंक र डाउनलिङ्क स्ट्रिम अनुपात वेब UI वा नियन्त्रण uart मार्फत नियन्त्रण गर्न सकिन्छ.
• Our module supports networking modes: बिन्दु-बाट-बिन्दु, Point-to-Multi-point, रिले, र जाल (specify mesh version when ordering).

MESH Centerless Networking