IP mesh radio transceiver module for drone video data link UHF Vcan2024

IP mesh radio transceiver module for drone video data link UHF

IP mesh radio transceiver module is suitable for point-to-multi-point or multi-point-to-multi-point network requirements.

उदाहरणार्थ, your project requires multiple transmitters and multiple receivers. Each node can act as a relay for other nodes. Each node cannot be individually defined as a transmitter, स्वीकारणारा, or repeater. Each node is a transmitter, a receiver, and a repeater. Such as security squads, bicycle racing, 2+ drones in the sky and 2+ receivers on the ground, आणि इतर अनुप्रयोग.

वैशिष्ट्य

1. Two-way bidirectional transmission video data download and upload
2. TDD OFDM full-duplex IP Mesh radio wireless transceiver module for video and data transmission
3. Dual RF Power: 24± 1 डीबीएम, 2-चॅनेल
4. Optional Working Frequency: 566~678MHz (112Mhz range hopping), 1420~1530MHz (110Mhz range hopping)
5. Three Ethernet RJ45 for video or data and One RS232 UART data link, control UART (TTL) पोर्ट
6. Support transmit distance: 500~2000 meters (हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते), 5~22km (हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते); For a longer range, we needed the extra power amplifier support. (2वॅट्स, 5वॅट्स, 10वॅट्स)
7. This board supports the CX6779K modem.

FHSS Frequency Hopping

• We designed this wireless video and data transmission with uplink and downlink for those who need the frequency automatic hopping function.
• With frequency hopping technology (हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते) to ensure better stable signal communication, when the current frequency signal is worse, the system will automatically change the working frequency to another frequency for a better signal.
• This bidirectional OFDM radio module can work from 566Mhz to 678MHz or from 1420Mhz to 1530MHz bandwidth. So the frequency range has 110Mhz bandwidth change or hopping. If you set the frequency bandwidth at 10 मेगाहर्ट्झ, then there are 11 frequency points for hopping.

तपशील

• हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते (Need FDD COFDM model?)
• समर्थन 2 Frequency ranges (566~678MHz/1420~1530MHz)
• Supports FHSS frequency automatic hopping function
• 4/3/5/10/20/40हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते
• Max 100Mbps throughput
• Dual RF transmission power: 24± 1 डीबीएम, 2-channel for uplink and downlink
• ग्रह: QPSK, 16QAM, 64QAM, हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते
• संवेदनशीलता: -95dBm (20MHz बँडविड्थ)
• Supports IP Video Data Transmission (3 इथरनेट पोर्ट)
• हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते (1X RS232, 1X TTL)
• Without extra PA, Up to 22km LOS (हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते) आणि 2 किमी LOS(हे मॉडेल टू-वे वायरलेस डेटा लिंकसह व्हिडिओ आणि डेटा वायरलेस ट्रांसमिशनसाठी डिझाइन केले होते)
• Can add 2watts, 5वॅट्स, किंवा 10 watts to support longer range
• Web UI and control UART for management
• पर्यायी अंतर ग्रेड
• पर्यायी अंतर ग्रेड (Video stream needs more and data streaming needs less)
• नेटवर्किंग मोड: One-to-one P2P, one-to-many P2MP, many-to-one MP2P, relay/repeater, mesh or swarm network。
• वीज वापर: <7प
• परिमाण: 80 नाम 57 x 9.1mm
• वजन: 41ग्रॅम
• Working Temperate: -20℃ ~ +65℃
• Storage Temperate: -40℃ ~ +80℃

IP Radio Module Connector (इनपुट / आउटपुट)

पर्यायी RS232	2PIN PH2.0mmConnector, DC in:9पर्यायी अंतर ग्रेड
इथरनेट-1	4PIN PH1.25mm कनेक्टर
इथरनेट-2	4PIN PH1.25mm कनेक्टर
Ethernet-3	4PIN PH1.25mm कनेक्टर
डेटा UART	3PIN PH1.25mm कनेक्टर, RS232(or TTL 3.3V)
UART नियंत्रित करा	3PIN PH1.25mm कनेक्टर, टीटीएल 3.3 व्ही
युएसबी	Micro USB Connector, for software upgrading
स्विच करा	Tx/Rx control signal for outside power amplifier
Main-Antenna	पर्यायी अंतर ग्रेड, IPEX
Second-Antenna	पर्यायी अंतर ग्रेड, IPEX
12व्ही बाहेर	On-board 12V out(<200मा), for cool fan power supply

पर्यायी अंतर ग्रेड, Ethernet2 and Ethernet3

The three Ethernet ports on board are bridged connections, so their IP addresses are the same. The photo below shows the 4PIN signals of the Ethernet port.

Switch Port

This port is a TX transmitter / RX receiver control signal for the extra power amplifier. The maximum RF transmission power of our module is 24±1dBm two channels, We also provide the correct power amplifier to increase the RF Power to 2-watt / 5-watt /10-watt if you need a longer range than 22km.

The below diagram shows how to add a power amplifier outside extra of this IP Radio Module.

This operation is for your reference only. If you need to add an external power amplifier, it is best to tell us and we will configure it for you, or ask a professional to operate it, अन्यथा, the PA will be easily burned.

सिग्नल	Electrical level	आय / ओ	वर्णन	mark
PA-enable1	1.8व्ही	द	High electrical level: data transmitting, change to high electrical level at 3.19us before transmitting and to low electrical level at 0.26us after transmitting finished.	High-Tx Low-Rx

डेटा UART

• The data UART is RS232 as default.
• We also can change the data port from RS232 to TTL 3.3V UART before the cargo delivery.
• The baud rate of data UART can be set as 115200, 57600, 38400, 19200, 9600, 4800, 2400, आणि 1200.

  

   

Control UART and USB port

Only one of these two ports is valid at the same time. Control UART is valid by default shipment. Please contact us if you need to use a USB UART. You can manage our module with Web UI or AT command via control UART.

LEDs light

LED1: पॉवर LED, लाल, light on normal powered.

LED2: blue, LED3: हिरवा, LED2 and LED3 indicate the wireless working status as described in the below table.

Central node	Blue LED2 light on all the time and green LED3 is not light
Access node	Green LED3 light on all the time when the access node is connected with the central node.
	The blue LED2 indicate the access node linking signal status with the central node. When the wireless linking signal is strong, blue LED2 blinks every 30 सेकंद; When the wireless linking signal is middle, blue LED2 blinks every 6 सेकंद; When the wireless linking signal is weak, blue LED2 blinks every 1 दुसरा.

Sometimes customers may need to assemble the indicating LEDs on their housing case panel, so our board also provides a soldering hole for the three LED signals. The LED signal is described in the below table.

एलईडी	वर्णन	Representation soldering hole
LED1	पॉवर LED	LED1-GND and LEDs-VCC
LED2	Wireless indicating LED	LED2-GND and LEDs-VCC
LED3		LED3-GND and LEDs-VCC

Wireless networking with the IP MESH Radio Module

• Our module supports two operating modes: प्रसारित नेटवर्क पद्धत. It can be managed through Web UI or AT command via control UART.
• Our module supports features of a maximum of 63 प्रसारित नेटवर्क पद्धत. All the Nodes are in the same wireless LAN and share the whole transmission bandwidth (maximum 100Mbps throughout).
• Data from the Central Node to the Access Node, प्रसारित नेटवर्क पद्धत, and data from the Access Node to the Central Node, प्रसारित नेटवर्क पद्धत.
• Uplink and downlink stream ratio can be controlled through web UI or AT command.
• When using Our module for Point-to-Point transmitting, अपलिंक आणि डाउनलिंक प्रवाह प्रमाण वेब UI किंवा Control uart द्वारे नियंत्रित केले जाऊ शकते (maximum 100Mbps throughout) अपलिंक आणि डाउनलिंक प्रवाह प्रमाण वेब UI किंवा Control uart द्वारे नियंत्रित केले जाऊ शकते.
• Our module supports networking modes: पर्यायी अंतर ग्रेड, Point-to-Multi-point, पर्यायी अंतर ग्रेड, पर्यायी अंतर ग्रेड (specify mesh version when ordering).

MESH Centerless Networking