Operate guide for Vcan1401-Mesh Ad hoc network communication module

Mesh Ad hoc network communication module

1. Brief introduction of ad hoc network communication module

Mobiilse iseorganiseeruva võrguna, Vcan1401-Mesh supports any network topology. Erinevalt tavapärastest traadita võrkudest, it is a wireless broadband system with no center, jaotatud, mitme hüppega relee, dünaamiline marsruutimine, strong invulnerability and good scalability. It uses its own routing protocol internally to complete the wireless communication between nodes through wireless multi-hop forwarding. Ad hoc hajutatud lairiba traadita võrgu edastussüsteem tõhusa MAC-kihi edastusprotokolli ja kahekihilise marsruutimisprotokolliga. All nodes are completely equal, without any infrastructure, and can quickly build a dedicated self-organizing network between mobile nodes, pakkuda kohest adaptiivset suhtlust, neil on suurepärane lairiba jõudlus, and support the real-time transmission of multimedia information such as video coding and audio coding. Süsteemitehnoloogia eelisteks on tugev häiretevastane võime, kõrge spektri efektiivsus, kaua edastamise kaugus, tuhmumisvastane võime, ja tugev difraktsioonivõime. See suudab realiseerida reaalajas ja kvaliteetseid traadita kahesuunalisi andmeedastusfunktsioone keerukates ja mittenähtavates keskkondades.

Vcan1401-Mesh series technical features

*Pole vaja seadistada keskjaama ja keerukat süsteemikonfiguratsiooni. Pärast saidi sisselülitamist, it will automatically form a network, and the communication can be started in “seconds”;

* Suvaline topoloogia, mitme hüppega relee, relee edastamine;

* Iga sõlme loogilisi atribuute saab paindlikult konfigureerida;

* Hetkel, sama sagedusvõrk võib toetada ≥32 sõlme omavahelist ühendamist;

* Kanal on krüpteeritud AES-iga;

* Süsteemi andmeside ribalaiuse tippväärtus on 90 Mbps;

* Tugev häiretevastane võime, kõrge spektri efektiivsus, kaua edastamise kaugus, sekkumisvastane

Tugev kukkumisvõime ja difraktsioonivõime

2. Tehnilised parameetrid

• Sidesagedus: 1412~1452MHz, adjustable in 5MHz steps;
• saatevõimsus: 2*30dBm (2*1W), 1dBm step adjustable。
• Ribalaiuse režiim: 5 / 10 / 20 MHz;
• modulatsioonimeetod: mitme kandjaga TDD-COFDM;
• Kandja modulatsioon: BPSK/QPSK/16QAM/64QAM (adaptiivne või fikseeritud);
• Saate tundlikkus: -98dBm @ 10MHz;

• Suhtluskaugus: 30km (maa-õhk/õhk-õhk-sihtliin), 8km (maa-maa vaatevälja);
• Suhtluskiirus: peak 90Mbps (kohanemisvõimeline);
• Edastamise viivitus: Single jump about 2ms；
• Mitme hüppe võimalus: kuni 8 videohüpped;
• Start time: ≤25S;
• Võrgule juurdepääsu aeg: vähem kui 1 teiseks;
• Marsruutimise ümberlülitamine: vähem kui 1 teiseks;
• andmeliides: network port x 2, RS232 x 2;
• Energiatarve: 2~8W
• Protection level: IP65;

• töötemperatuur: -40~ +70 ℃;
• mõõdud: pikkus: 72.8mm*width 47.3mm*height 17.9mm
• kaal: 78g

2. Software operation instructions

Support 5M, 10M, and 20M bandwidth, real-time graphical interface display, real-time map indication, jne.

The software disables DHCP by default, and the default IP address is 192.168.17.1 If you forget the address, please connect the 9th pin of the 26PIN cable to the ground to reset the parameters.

Enter the IP address of the module in the browser, and the default username and password are both admin. It takes about 20s for the module to connect to the network from power-on. The recommended browser is Chrome.

After entering, it defaults to simple mode, click expert mode to unlock more settings, suitable for professional debugging.

3. Status section:

Ülevaade:

Topology map: (automatic refresh is turned off by default to save bandwidth, you can check automatic refresh)

Check only the display path, you can know the direct jump point relationship of each module

Check the details to judge the data connection status of each module. These are displayed dynamically in real time

Click Details: You can know the specific situation of each module directly:

Terminal state:

Ad hoc network: You can remark the name, muidugi, it can also be operated in the terminal state.

Spektri skaneerimine: Check the interference of each frequency band. Muidugi, the frequency bands of different modules are purchased, and the scanning frequency bands are different.

Map: (Muidugi, to know the location information of each terminal, GNSS modules such as GPS or Beidou need to be installed)

Support tile maps, image maps, network maps, jne.

Configuration section:

viis: 1. MESH node or bridge configuration

2. Wireless configuration:

2.1 Transmission power configuration, the power of different products purchased is different.

kanal ribalaius: 5M 10M 20M 40M

kanal: Different channels are used to purchase different products

The coverage distance (meetri) needs to be filled in according to the actual situation. If it is set to 3000 meetri, it is impossible to actually run to 5000 meetri.

Number of Antennas 2

Fixed MCS rate: Can be set to off for automatic selection. If you want stable transmission, it is recommended to set the manual, valik (MCS0 to MCS15)

Bandwidth, modulatsioon, määr

Limit MCS rate: It is recommended to enable it. After enabling it, if the fixed rate is MCS4, the software will automatically select the best modulation method from MCS0 to MCS4 during the test.

		5M	10M	20M	40M
MCS0	BPSK 1/2	1.7M	3.3m	6.5M	13.5M
MCS1	QPSK 1/2	3.2m	6.5M	13m	27m
MCS2	QPSK 3/4	4.8m	9.8m	19.5M	40.5M
MCS3	16QAM 1/2	6.5M	13m	26M	54M
MCS4	16QAM 3/4	9.7M	19.5M	39M	81M
MCS5	64QAM 2/3	13m	26M	52m	108M
MCS6	64QAM 3/4	14.5M	29M	58.5M	121M
MCS7	64QAM 5/6	16M	32.5M	65m	135M
MCS8	BPSK 1/2	3.2m	6.5M	13m	27m
MCS9	QPSK 1/2	6.5M	13m	26M	54M
MCS10	QPSK 3/4	9.7M	19.5M	39M	81M
MCS11	16QAM 1/2	13m	26M	52m	108M
MCS12	16QAM 3/4	19.5M	39M	78M	162M
MCS13	64QAM 2/3	26M	52m	104M	216M
MCS14	64QAM 3/4	29M	58.5M	117M	243M
MCS15	64QAM 5/6	32.5M	65m	130M	270M

From MCS0 to MCS7, two wireless ports send the same data in order to improve stability during the movement.

From MCS8 to MCS15, the two wireless ports send different data, which can make the rate X2

If it is in a mobile state, it is recommended to use BPSK or QPSK to transmit data. 16QAM and 64QAM are suitable for use with fixed transmission.

If MCS8 to MCS15 is used, it is recommended that the antennas of the two ports be 90 degrees to each other, näiteks, one is vertical and the other is horizontal.

If drones are used, MCS0 to MCS2 is recommended.

The greater the bandwidth, the lower the sensitivity. The same goes for modulation.

above rate unitbps

3. võrk:

4. User management:

5. süsteem

6. Tools Configure serial port, GPS/Beidou/GNSS, 4G/5G access and other parameters

6.1 Multi-device management, in the upper right corner, you can log in and manage users remotely, and it is also a real-time dynamic interface display or map display.

6.2 Serial port software settings:

Select Expert Mode, töövahendid, and UART Interface.

choose new

Tähelepanu!, if you use the serial port to transmit serial data, you have to choose ttyS0 (COM1 of hardware) and ttyUSB0 (COM2 of hardware), ttyATH0 is invalid, režiimis: network

boodikiirus 115200, stoppbitt 1, parity none.

nimi 1, protocol UDP, IP address, 192.168.55.100 (the IP address here is the IP address of the other device, näiteks, input the IP of the computer for the computer, and input the IP of the device for the device).

port 20005, 20003. Choose a port number

The computer’s IP is set to a fixed 192.168.17.100

Short the TX RX pins of COM1 and COM2 of the device.

Use the TCP UDP test tool to fill in the IP and port of the device.

Send to loop back data.