የመለኪያ ውቅረት ፓነል ፈጣን የስራ መመሪያ ለ COFDM ሽቦ አልባ ቪዲዮ አስተላላፊ እና ተቀባይ

When using the COFDM transceiver module (or transmitter and receiver complete set), it may be necessary to modify the configuration parameters of the module. For the convenience of customers, We have developed the LCD panel board for parameter configuration, the details are as follows:

Parameter configuration panel Quick Operation Guide

1 User interface introduction

1.1 OLED screen display:

This configuration panel board is equipped with a 0.96-inch OLED display, which is used to display the parameters of the COFDM transceiver module (center frequency point, የመተላለፊያ, ወዘተ) for users to query and modify.

1.2 Input buttons:

The configuration panel board has 3 function buttons, which are used to switch parameter display or edit and modify parameter values as needed.

2 How to use

2.1 Parameter display:

When it is powered on, the LCD will display “Connect To Target Device”.

When the configuration Panel board and COFDM transceiver module communicate successfully, the monitor will display the acquired parameter value of the transceiver module. The basic parameter page is displayed by default, and then short pressing the “ወደላይ” ወይም “ታች” switch to the advanced parameter page.

3. Transmitter interface

3.1 basic parameter page of the

COFDM TX V xx

3.2 advanced parameter page

COFDM TX V xx

4. Receiver interface

4.1 basic parameter page

4.2 Advanced parameter page

5. Parameter Modification:

The basic parameter page is displayed by default, If users need to view or modify advanced parameters, they can short press the “ወደላይ” ወይም “ታች” button to switch to the advanced parameter page.

In the default mode, only the parameters can be previewed. If the user needs to modify the parameters, please long-press the “ምናሌ” button to enter the parameter editing mode.

In the edit mode, the edited parameter value will flash and prompt, if the customer needs to switch the parameter, long-press the “ወደላይ” ወይም “ታች” button to switch. If you don’t need to switch parameters, you can short press the “ምናሌ” button to switch the high and low bits of the parameter to be edited, the corresponding edited bit will flash and prompt, and then press “ወደላይ” ወይም “ታች” button to increase or decrease the value of the corresponding bit of the parameter.

After modifying the parameters (allowing to change multiple parameters at once), Long-press the “MENU” button, and the current parameters will all flash ( parameter name and parameter value flash together), then release the “ምናሌ” button to complete the editing and exit the editing mode, The new parameter value will be written into the COFDM transceiver module.

6. Input and switch the most used frequency points

At Default mode, press and hold the “ወደላይ” ና “DOWN“ two buttons for 2-3 ሰከንዶች, then enter the most used frequency point input page (Allow to set 4 most used frequency points):

If you have not entered common frequency points before, then all common frequency points will be displayed as 000000 (representing Not set); if common frequency points have been set before, the value of the corresponding frequency point will be displayed.

In the most used frequency point input page, the edited frequency point parameter will flash and prompt if the customer needs to switch the frequency point, long press the “ወደላይ” ወይም “ታች” button to switch. If you do not need to switch the frequency point, you can short press the “ምናሌ” button to switch the high and low digits of the frequency point parameter that needs to be edited, the edited digit will flash and prompt, and then press “ወደላይ” ወይም “ታች” button to increase or decrease the digit of the parameter (If you want to cancel a frequency point, change the parameter of the frequency point to 000000).

After modifying the frequency parameters (Allowing to modify of multiple parameters at one time), Long-press the “ምናሌ” አዝራር, and all current parameters will flash ( parameter name and parameter value flash together), then release the “ምናሌ” button to complete the editing and exit the most used frequency point input page, return to the basic parameter page, and the new frequency point parameter value will be recorded in the configuration panel.

7. Switch the most used frequency point

At default mode, long-press the “ወደላይ” ወይም “ታች” አዝራር, and it will switch the pre-set entered the most used frequency points. (allowed to switch at up to 4 most used frequency points ), and the current switch will be displayed on the screen To the frequency point (displayed in the center and in large font), and return to the basic parameter page after staying for 5 ሰከንዶች:   

የቅርብ ጊዜ 2 ዋ የኃይል ማጉያ 27 KM የረዥም ርቀት ሽቦ አልባ ቪዲዮ አስተላላፊ ተቀባይ ሕያው የማሳያ ምስል ዳታ ማገናኛ ማስተላለፍ ውስጥ 2022

ለደንበኞቻችን ትክክለኛውን የድጋፍ ርቀት በተሻለ ሁኔታ ለማሳየት እና የ 2W PA 30km የረጅም ርቀት ምስል ማስተላለፊያ እና መቀበያ ውጤትን ለመጠቀም, በቅርቡ ትክክለኛ ሙከራ አድርገናል እና Meisha Peak አግኝተናል, ከዚህ ወደ ናናኦ ባህር ዳርቻ, ርቀቱ ነው። 27 ኪሎሜትሮች. ይህ [...]

ተጨማሪ ያንብቡ

06
የካቲት

አዲስ የረዥም ርቀት ገመድ አልባ ቪዲዮ አስተላላፊ እና ተቀባይ ለድሮን ካሜራ 110 ኪ.ሜ 10 ዋ ፒኤ ገመድ አልባ ቪዲዮ ዳታ የድምጽ ማገናኛ እውነተኛ ሙከራ

110ኪሜ የረጅም ርቀት ሽቦ አልባ ቪዲዮ አስተላላፊ እና ተቀባይ ቪዲዮ ለድሮን ቪዲዮ ካሜራ ለምን ይህን የ110 ኪሎ ሜትር የርቀት ሙከራ ማድረግ እንፈልጋለን? አንዳንድ ደንበኞች የገመድ አልባ ቪዲዮ አስተላላፊ እና ተቀባይ ረጅሙን ርቀት ይጠይቁኛል።, አሁን ይህንን 10W Power Amplifier ሞዴል መከርን, [...]

ተጨማሪ ያንብቡ

07
ኦክቶበር

የቅርብ ጊዜ የገመድ አልባ ቪዲዮ ውሂብ ኦዲዮ አስተላላፊ እና ተቀባይ ሙከራ ቪዲዮ ውስጥ 2022

ሽቦ አልባ ቪዲዮ ዳታ ኦዲዮ አስተላላፊ እና ተቀባይ TX900 2 ዋትስ 27 ኪሜ የሙከራ ቪዲዮ ከተራራ ጫፍ እስከ ባህር ዳርቻ. (ቪዲዮ ከውስጥ) ሽቦ አልባ ቪዲዮ ዳታ ኦዲዮ አስተላላፊ እና ተቀባይ, ባለሁለት መንገድ, አውርድ-አፕሎድ ደንበኛ ስለእኛ እውነተኛ የሙከራ ቪዲዮ አይቷል። 2 ዋትስ ፓወር አምፕሊፋየር 27 ኪሎ ሜትር የረዥም ርቀት ሽቦ አልባ ቪዲዮ አስተላላፊ እና ተቀባይ. እሱ [...]

ተጨማሪ ያንብቡ

01
ሴፕቴምበር

60-80 ኪሜ የገመድ አልባ ቪዲዮ አስተላላፊ መቀበያ ስርጭት በእውነቱ በራሪ ሙከራ

በእውነቱ የድሮን የበረራ ሙከራ 60-80 ኪሜ ሽቦ አልባ ቪዲዮ አስተላላፊ መቀበያ ማስተላለፊያ ይህ ለድሮን UAV ካሜራዎች የቪዲዮ ማስተላለፊያ እና ተቀባይ ነው።, ውስጥ ምርጥ 2023, እና ብዙ እርካታ ያላቸው ግምገማዎች አሉት. እንዲሁም ከመሬት ወደ መሬት ይደግፋል, የቪዲዮ ማስተላለፊያ የሚፈልግ ማንኛውም ፕሮጀክት ካለዎት [...]

ተጨማሪ ያንብቡ

24
ኦክቶበር