የ OSD ማሳያ ተግባር በ COFDM መቀበያ ላይ

Key1: turn on/off the status of the OSD displaying, ለመቀየር በረጅሙ ይጫኑት።(ከ 1 በላይ). the status will be kept after reboot. ከውሂብ uart ምንም የ OSD ውሂብ ግብዓት ሳይኖር የ OSD ሁኔታ ሲበራ, መሣሪያው በቪዲዮ ስክሪን ላይ መረጃን ያሳያል:

በሪቻርድ：338.0ሜኸ ኢንዶነዥያ：4.0ሜኸ; በሪቻርድ, የሥራ ድግግሞሽ; ኢንዶነዥያ, የመተላለፊያ

QPSK CR：2/3 ጂ:1/16; የህብረ-, FEC, ጋርድ ክፍተት.

የአየር：3.90ሜጋ ባይት; የአየር, ሽቦ አልባ ማስተላለፊያ ቢትሬትስ

VBR：3.05ሜጋ aes ጠፍቷል; VBR, የቪዲዮ ቢትሬትስ; aes ጠፍቷል, የAES ምስጠራ ጠፍቷል.

SIG1：27 SIG2：22; SIG1, signal intensity of ant 1; SIG2, signal intensity of ant 2

ber1:0.14% ber2:100.00%; ber1, bit error rate of ant 1; ber2, bit error rate of ant 2

ምንም ማከማቻ ጠፍቷል ቅዳ; የቪዲዮ ቀረጻ ሁኔታ

What is VBR? VBR is the video encoding bit rate at the transmitter. Since the video picture changes dynamically, VBR is of course variable, but it fluctuates around the encoding bit rate set by the transmission system: 7.81*0.8=6.248Mbps

How to use OSD API in Our COFDM systems?

Steps description:

1) The customer’s module sends the digital data to our COFDM transmitter via UART;

2) Our transmitter will send the digital data with video data together to our COFDM receiver via the wireless link;

3) Our receiver will send out the digital data to the customer’s module via UART;

4) The customer’s module should transfer the digital data into the characters string they want to show on the video screen in OSD mode. Then the customer’s module sends the characters string to our receiver via the same UART.

5) Our receiver will display the character’s string on the HDMI display screen with the video together in OSD mode.

API of Our COFDM receiver:

ትእዛዝ	ATOSD$(font), $(x),$(y),$(str) _ለምሳሌ：ATOSD1,40,20,height: 100m_
መለኪያዎች	font: 0: 8×16, ፒክሴል; 1: 16×24, ፒክሴል; x: 0 ወደ 1919, horizontal axis; ና: 0 ወደ 1079, vertical axis; Str: characters string start to show on the HDMI screen from (x,y) point; space characters used for a clean screen at that point. Since ’_’ is the command end flag, No ’_’ can be used in these parameters.
ሥራ	To display the characters string on the HDMI screen with the video in OSD mode
መመለስ	Null
መግለጫ	1) This command is used for the customer’s MCU module to our Receiver via data UART; 2) You can use ATST ትእዛዝ(described in other documents) to define our Receiver UART; 3) You should draw the HDMI screen following 1920*1080 pixels via (x,y) axis. Our receiver firmware will adjust it automatically according to the real screen systems.