Encoder Modulator Dekodeerder Demodulator Module Parameter Konfigurasie Instruksies COFDM AT Command

Download the Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions below if you need a PDF file.

Click to access Encoder-Modulator-and-Decoder-Demodulator.pdf

Update Record:

weergawe	datum	beskrywing
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1	2016-10-24 2016-11-1 2016-12-26 2017-2-14 2017-2-28 2017-3-27 2017-4-19 2017-5-18 2017-9-12 2018-3-15 2019-6-25 2023-2-24	Initial version ATDR reply distinguishing module ATSE, ATGE add audio switch Add ATSP protocol Add ATST, ATGT protocol ATGE command add AESfor status acquisition Added ATGB protocol AV and HDMI output control Support for obtaining the current AV output standard Added ATSU, ATGUcommands Added ATOSD, ATSIP, ATGIP commands Added ATSAD, ATGAD commands

Users may need to modify the configuration parameters of the module during the use of the COFDM modulator and demodulator module. In order to simplify the user’s operation, we design the parameter configuration into a few simple AT commands. The user only needs to use the specified AT command and pass the corresponding parameters to complete the parameter setting of the COFDM module.

Suitable Models

Command Introduction

The AT command for configuring COFDM module parameters starts with “BY” and ends with an underscore “_”. Each AT command has several or no parameters, and each AT command has a return value. For details, please refer to the introduction of the following commands.

Users can configure the parameters of the module through the configuration serial port (TTL vlak, 3.3V) of the COFDM module. For detailed serial port configuration, refer to the figure below. Please use tools such as “Serial Port Debugging Assistant” to send AT commands to the COFDM module, pay attention to the use of teks, byvoorbeeld:

Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions COFDM AT Command 1 — Encoder Modulator Decoder Demodulator Module

Command Classification

The AT commands for configuring COFDM module parameters are mainly divided into the following two categories:

Query Commands	ATDR, ATGD, ATGE, ATGI , ATGR, ATGT, ATGB, ATGU, ATGIP
Setting Commands	ATSD, ATSG, ATSM, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU,ATOSD, ATSIP

From the perspective of whether to save after power-off, the setting commands can be divided into:

Power-off Saving Commands	ATSD, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU, ATSIP
Power-off Not Saving Commands	ATSG, ATSM, ATOSD

According to the configuration transmitter or receiver, the classification is as follows:

Sender Configuration Commands	ATDR, ATSD, ATGD, ATSG, ATSM, ATSE, ATGE, ATSI, ATGI, ATSO, ATSP, ATST, ATGT, ATSU, ATGU, ATOSD
Receiver Configuration Commands	ATDR, ATSR, ATGR, ATSP, ATST, ATGT, ATGB, ATSIP, ATGIP

Command Details

Ping Command

formaat	ATDR_
parameter	Geen
Gebruik	for the integrated system to check whether the serial port is connected and identify the connected modules.
Retourwaarde	RCB returns the “device profile” string SUE1 returns “ATDRSUE1 OK” string SHD1 returns “ATDRSHD1 OK” string
opmerking	navraag opdrag

Set Device Command

C:\Users\timyep\AppData\Roaming\Tencent\Users\157871537\QQ\WinTemp\RichOle\E0XEBCD_M4WD[M1BWR$}TK4.png

Set Gain Command

formaat	ATSG$( tx1_gain),$( tx1_gain)_ Voorbeeld: ATSG85.0,85.0_
parameter	tx1_gain: sender 1 wins tx2_gain: sender 2 wins
Gebruik	To dynamically adjust the output power. If the signal SNR/RSSI of the receiver is high, the output power can be reduced through the remote control link. When the SNR/RSSI of the end signal is low, increase the output power (sender)
Terugkeerwaarde,	Voorbeeld: ATSG85.0,85.0_set gain 85.000000 85.000000 OK
opmerking	instelling opdrag, power off will not save.

Set Modulation Mode command

formaat	ATSM$(gi), $(Sentrale bedryfsfrekwensiepunt), $(constellation)_ Voorbeeld: ATSM1,1,2_
parameter	Gard interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1 /4; Convolution code rate: 0 1/2; 1 2/3; 2 3/4; 3 5/6; 4 7/8; konstellasie: 0 QPSK; 1 QAM16; 2 QAM64
Gebruik	Dynamically adjust the air interface rate, the air interface rate can be increased when the distance is short, and the air interface rate can be reduced when the distance is long (sender)
Terugkeerwaarde	Voorbeeld:ATSM1,1,2_GI:1/16, CR:2/3, MOD: QAM64, OK
opmerking	instelling opdrag, power off will not save.

Get Device Status Command

formaat	ATGD_
parameter	Geen
Gebruik	query the current number of transmit antennas, wag interval, convolution code rate, number of constellations, transmit frequency, bandwydte, gain parameters (sender)
Terugkeerwaarde	Voorbeeld: ATGD_ SISO, GI:1 /16, CR: 1/2, MOD: QPSK, frek: 800000KHz, bw: 8000KHz, tx1_gain: 86.000000 tx2_gain: 86.000000 OK
opmerking	navraag opdrag

Set Encoder Command

formaat	ATSE$(llc),$(rt),$(bitrate) ,$(gop),$(klank)_ Voorbeeld: ATSE0,0,0.0,0,0_
parameter	1. Enhanced data reliability option llc: 0 disable; 1 enable (requires the receiving end to enable this option at the same time, use in pairs, because more redundant data is added to enhance reliability, the video bit rate of the transmitting end should be set when this option is turned off half of) 2. Real-time priority/quality priority rt: 0 image quality priority; 1 real-time priority; 3. bitrate: 0 let system decide; >0 specify bitrate(float) 4. I frame interval GOP: 0 let system decide; >0 specify GOP 5. Audio encoding option audio: 0 disable; 1 enable
Gebruik	Used to set encoding parameters (sender)
Terugkeerwaarde	Voorbeeld:ATSE0, 0,0.0,0,0_ WYSE:0,RT:0,bitrate: 0.0Mbps,gop:0,klank:0,OK
opmerking	instelling opdrag, save when power is off.

Get Encoder Command

formaat	ATGE_
parameter	Geen
Gebruik	querying encoding parameters (sending end)
Terugkeerwaarde	Voorbeeld:ATGE_MODE:0, RT:0,bitrate:4.0Mbps,gop:10,klank:0,aes:0, OK
opmerking	Query command AES means the current encryption status: 0 disable; 1 enable

Get Input Command

formaat	ATGI_
parameter	Geen
Gebruik	query the current camera input parameters (sender)
Terugkeerwaarde	Voorbeeld:ATGI_input_size: 1080p, input_rate: 60fps, sensor_type: hdmi,OK
opmerking	navraag opdrag

Set Input Command

formaat	ATSI$(input_size),$(input_rate)_ Voorbeeld: ATSI1080,25_
parameter	1. Input resolution input_size: 0 laat die stelsel opspoor; >0 specify input size 2. Input frame rate input_rate: 0 laat die stelsel opspoor; > 0 specify input fps
Gebruik	To specify the input resolution and frame rate to meet some special signal sources, or some special application needs (sender)
Terugkeerwaarde	Voorbeeld: ATSI1080,25_ Input_size:1080p,input_rate: 25fps, OK
opmerkings	After the user specifies the input resolution and frame rate through this command, the system will no longer detect the signal source (use with caution). The user can restore the default through the following command: ATSI0,0_Set the command and save it after power-off.

Set Output Command

formaat	ATSO$(output_size),$(output_rate)_ Voorbeeld: ATSO720,30_
parameter	1. sender: encoding output resolution output_size: 0 equal to input_size; >0 specify output size 2. ontvanger: HDMI output resolution (720, 1080) 3. sender: encoding output frame rate output_rate: 0 equal to input_rate; >0 specify output_rate (fps) 4. ontvanger: HDMI output frame rate 720p supports frame rate (50, 60); 1080p supports frame rate (24, 25, 30, 50, 60)
Gebruik	1. sender: Used to specify the encoding output resolution and frame rate to meet the requirements of certain applications for zooming and frame reduction 2. ontvanger: used to configure the resolution and frame rate of HDMI output
Terugkeerwaarde	Voorbeeld: ATSO720,30_ output_size: 720p, output_rate: 30fps, OK
opmerkings	1. For HDMI input only, this command is invalid for AV input 2. Output_size <= input_size; output_rate<=input_rate 3. Set the command and save it after the power is off.

Stel Invoerbronne-opdrag (skakel HDMI / CVBS insette)

formaat	ATSU$(vin),$(ain)_ Voorbeeld: ATSU0,1_
parameter	1. Video-invoerkeuse VIN: 0 laat die stelsel opspoor; 1 dwing CVBS-invoer; 2 dwing hdmi/SDI-invoer 2. Oudio-invoerkeuse AIN: 0 laat die stelsel opspoor; 1 dwing analoog insette
Gebruik	Word gebruik om aan spesifieke toepassingsvereistes te voldoen (Voorbeeld: HDMI/SDI-invoervideo, MIC-invoer klank)
Terugkeerwaarde	Voorbeeld: ATSU0,1_ ATSU0,1 OK
opmerking	instelling opdrag, power-off save.

Get User Command

formaat	ATGU _ Voorbeeld: ATGU_
parameter	Geen
Gebruik	To query user-specific configuration
Terugkeerwaarde	Voorbeeld: ATGU_ ATGU0,1 OK
opmerking	navraag opdrag return parameter description please refer to the ATSU command

Set Receiver Command

formaat	ATSR $(frek), $(bw ), $(llc), $(cvbs)_ Voorbeeld: ATSR320000,6000,0,0_
parameter	1. DR2C carrier frequency freq(KHz) 200000~860000(200MHz ~ 860MHz, 1KHz-stap) 2. DR900 carrier center frequency freq(KHz) 200000~1600000(200MHz~1.6GHz, 1KHz-stap) 3. DR2C channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1KHz-stap) 4. DR900 channel bandwidth bw(KHz) 3200~8000(3.2MHz~8MHz, 1KHz-stap) 5. Enhanced data reliability option llc: 0 disable; 1 enable (it is required that the transmitter should also enable this option at the same time, and use it in pairs. Since more redundant data is added to enhance reliability, the video bit rate of the transmitter should be set to when this option is turned off half of) 6. AV output system cvbs: 0 pal; 1 ntsc
Gebruik	To set the receiver parameter
Terugkeerwaarde	example: ATSR320000,6000,0,0_ ATSR320000,6000,0,0 OK
opmerking	instelling opdrag, save when power is off.

Get Receiver Command

formaat	ATGR_
parameter	Geen
ATGR_	the receiving end parameter
Terugkeerwaarde	Voorbeeld: ATGR_ ATGR320000,6000,0,aes:0,cvbs:0 OK
opmerking	1. Query command 2. Aes parameter indicates the current encryption status: 0 disable;1 enable 3. CVBS parameter Indicates the current AV output standard: 0 pal;1 ntsc

Get Bit Error Rate Command

formaat	ATGB_
parameter	Geen
Gebruik	querying the bit error rate and signal strength of the dual antennas at the receiving end
Terugkeerwaarde	Voorbeeld: ATGB_ ATGB ber1:0.00% ber2:0.00% RSSI1 :54 RSSI2:53 Lock1:1 Lock2:1 OK
opmerkings	1. Query commands 2. Ber1 and ber2 respectively indicate the bit error rate of each antenna, ranging from 0.0% om 100.0% 3. RSSI1 and RSSI2 respectively indicate the signal strength of each antenna, ranging from 0 om 100 4. Lock1 and Lock2 respectively indicate the signal locking status of each antenna (1 Represents signal lock)

Set Password Command

formaat	ATSP$(wagwoord), $(wagwoord)_ Voorbeeld: ATSP123456, 123456_
parameter	AES key password: 6-digit password (ASCII) AES key password: 6-digit password (ASCII) (repeat it for confirmation)
Gebruik	Used to set the AES key of the transceiver (sender en ontvanger)
Terugkeerwaarde	Voorbeeld: ATSP123456_ ATSP123456 OK
opmerking	1. When the password is all 0, AES encryption is turned off. 2. Set the command and save it after powering it off.

Set Data Transfer Command

formaat	ATST$(baud koers), $( parity)_ Voorbeeld: ATST115200,0_
parameter	1. Baud rate baud rate: 1200、2400、4800、9600、19200、38400、57600、115200 2. Check Code: 0: Geen; 1: Odd; 2: Even
Gebruik	Used to set the baud rate and parity bit of the serial port for data transparent transmission
Terugkeerwaarde	Voorbeeld: ATST115200,0_ ATST115200,0 OK
opmerkings	Set command

Get Data Transfer Command

formaat	ATGT_
parameter	Geen
Gebruik	Used to query the baud rate and check code
Terugkeerwaarde	Voorbeeld: ATGT_ ATGT115200,0 OK
opmerkings	Query command

Set IP Address Command

formaat	ATSIP$(ip), $(ip)_ Voorbeeld: ATSIP192.168.1.215,192.168.1.215_
Parameters	Local IP address Local IP address (repeat to confirm)
Gebruik	Used to set the receiver IP address
Terugkeerwaarde	Voorbeeld: ATSIP_192.168.1 .215,192.168.1.215_ ATSIP192.168.1.215 OK
opmerkings	1. After setting the IP address, the receiving end needs to be restarted to take effect. 2. Set the command and save it after powering it off.

Get IP Address Command

formaat	ATGIP_ Voorbeeld: ATGIP_
parameter	Geen
Gebruik	om die huidige IP-adres van die ontvangerkant te bevraagteken
Retourwaarde	Voorbeeld: ATGIP_ ATGIP192.168.0.215 OK
opmerking	navraag opdrag

OSD Overlay Protocol

formaat	ATOSD$(idx), $(x), $(en), $(str)_ Voorbeeld:ATOSD0,40,20,height: 100m_
parameter	1. IDX index: 0~7 (supports OSD overlay for 8 areas) 2. X-coordinate: 0~1919 3. Y coordinate: 0~1079 4. str: the string to be displayed at the corresponding coordinates (the space symbol is used to clear the display)
Gebruik	on the video screen.OSD information
Retourwaarde	Geen
opmerkings	1. The user specifies the x and y coordinates of the OSD display according to the maximum 1920×1080 pixels, and the system will correct the coordinates according to the actual display situation. 2. The ‘_’ character cannot be contained in the str parameter

Set Gain To Adjust

formaat	ATSAD$(frek),$(adjust) _ Voorbeeld:ATSAD700000,2.5_
parameter	wireless central working frequency： Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) Adjust the value(dB): ATSD cmd will subtract this value to set the wireless gain
funksie	Specify and adjust the value for the wireless gain setting using by ATSD cmd
terugvoer	Voorbeeld: ATSAD700000,2.5_ freq:700000,adjust:2.50 OK
Kommentaar	Setting command is still valid when stopping power or resetting.

Get Gain To Adjust

formaat	ATGAD[$(frek)]_ Voorbeeld:ATGAD700000_
parameter	wireless central working frequency： Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) When no parameter provides, it will list all the freq that have adjusted value.
funksie	Inquiry adjust the value for wireless gain setting using ATSD cmd
terugvoer	Voorbeeld: ATGAD700000_ freq:700000,adjust:2.50 OK ATGAD_ freq:700000 750000 OK
Kommentaar	Inquiry command.

Serial Port Utility software download

https://www.alithon.com/downloads

Vrae

1. How can I return to the No Password setting with 000000 indications after the change?

Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board.
or set it through die ATSP_command

2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (wins) good for linear output operation? Or do you suggest some limited range for better linear operation?

The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output:
1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm.
2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.

3. I tried to set – B bandwidth (kHz) and E bit rate (Mbps). When I set E, the new value does not apply. So. the E setting is only for monitoring of available bitrate? if I wish to change the E (bitrate) I have to change only B (bandwydte)? Am I right?

It is not recommended to modify the video bit rate ‘E’ directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally.
By default, the internal video bit rate ‘E’ will be set to 0 for automatic. Customers only need to modify ‘B’ to modify the wireless parameters, and the video bit rate will automatically adapt.
You can also adjust the wireless air interface rate by modifying GI and CR.

For more details on the Encoder Modulator Decoder Demodulator Module, please send an inquiry to us.

filter

COFDM Modulator-Demodulator Module 2X video Encoder-Decoder Board hdmi cvbs low latency

Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Input AES 256 FHD RF streaming COFDM

drone uav low latency COFDM Modulator-Demodulator Module Encoder-Decoder Board hdmi cvbs

COFDM Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Invoer AES 256 FHD RF-stroom

Q: 1. How can I return to the No Password setting with 000000 indications after the change?

Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board. or set it through the ATSP _command

Q: 2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (Gain) good for linear output operation? Or do you suggest some limited range for better linear operation?

The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output: 1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm. 2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.

Q: 3. I tried to set - B bandwidth (kHz) and E bit rate (Mbps). When I set E, the new value does not apply. So. the E setting is only for monitoring of available bitrate? if I wish to change the E (Bitrate) I have to change only B (bandwidth)? Am I right?

It is not recommended to modify the video bit rate 'E' directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally. By default, the internal video bit rate 'E' will be set to 0 for automatic. Customers only need to modify 'B' to modify the wireless parameters, and the video bit rate will automatically adapt. You can also adjust the wireless air interface rate by modifying GI and CR.

SKU: Vcan1776 kategorieë: COFDM, TX RX-module, Eenrigting eenrigting Tags: COFDM, cofdm demodulator, Eenrigting

COFDM Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Invoer AES 256 FHD RF-stroom

INHOUDSOPGAWE

Another side view

Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Input AES 256 FHD RF streaming parameter configuration board — COFDM Modulator Demodulator HDMI CVBS Module Encoder Decoder HDMI CVBS AV Input AES 256 FHD RF streaming parameter configuration board

COFDM Encoder module, CVBS / HDMI insette, IP-uitset

Composite CVBS input IP RJ45 Ethernet output Ultra-low latency encoder board, HDMI CVBS Encoder — Saamgestelde CVBS-invoer IP RJ45 Ethernet-uitset Ultra-lae latensie-enkodeerderbord, HDMI CVBS Encoder

For More details about the COFDM encoder board, please visit here

COFDM Encoder module Advantage:

Ultra-lae vertraging H.265/H.264 oudio- en video-enkodering maksimum ondersteuning 1080P@60 intydse video-opname en -kodering
HDMI- of AV-klank- en video-invoer, na enkodering, die Ethernet-poortuitvoer of Uitvoer na draadlose module, video-enkoderingsbiskoers kan dinamies gekonfigureer word
Ondersteun klank insette en klank dekodering uitset
Ondersteun twee video's (HDMI + AV) gelyktydige invoerkodering (opsie, die verstek is HDMI- of AV-kodering, kies een uit twee insetbronne). )
Web UI of seriële poort UART AT opdrag for configuration management

HDMI CVBS composite SDI video input encoder board digital IP ethernet output H264 H265 module board — HDMI CVBS saamgestelde SDI video-invoer-enkodeerderbord digitale IP ethernet-uitset H264 H265-modulebord

COFDM transmitter module

COFDM Wireless video transmitter module RCB board

Change RF connector from IPEX to MMCX for COFDM wireless video transmitter encoder modulator board

COFDM modulator-demodulator datasheet download

COFDM demodulator Vcan1776RX-H264 datasheet

The last version of the TX RX board

TX: V6.5.6p

RX: 4.1.2p

Gereelde vrae

1. What should I do when I found one Tx module doesn't generate RF output power?

Question1: Could you please tell me part number of this component, we try to find localy and check. antwoord 1: It is a inductance named LOH32PN2R2NNC.

COFDM-Transmitter-Module-no-tx output power

Suggest Check Points: If the power supply current of the board is well but there is no RF output, maybe the below component TC1-1-13MX+ is generally damaged.
In order to avoid damage to this device during transportation (the device itself is relatively high), we ordered red glue protection for this device when we shipped it.

The engineer also suggests that you check to see if the cable is loose or in poor contact.
Please try to replace the FPC cable connecting the two boards
We can provide spare parts if you're sure which one.

2. Can you offer me the UART AT command file for this model?

Sekerlik

Gaan asseblief die onderstaande skakel na.

Encoder Modulator Dekodeerder Demodulator Module Parameter Konfigurasie Instruksies COFDM AT Command

3. How does this COFDM Video transmitter and receiver support an IP camera?

1. It is not easy to connect to IPC for a one-way COFDM link. We have an H264 model, which is connected to IPC input by expanding the network port, but there are requirements for IPC models (not all models of IPC can be well connected with COFDM links), we have tested the IPCs of Hikvision, Dahua, and Xiongmai, and found that the connection effect of Hikvision is quite ideal.

2. It is impossible to directly remove the HDMI CVBS encoder and connect the IP Camera to the COFDM Transmitter board. One-way COFDM connection to IPC requires special technical methods to realize.

3. The best way is to recommend using our two-way image transmission transceiver, which directly supports the IP camera.

4. If the customer must use the COFDM transmitter board to support the IP camera, there are two points to pay attention to.

5. The first point is a technical problem. We need to use an alternative method to allow unidirectional COFDM links to be used with IPC.

6.If you consider IPC from the perspective of cost reduction, you don't need to consider it. Because the encoding board and decoding board are still necessary, the cost cannot be saved.

7. The second point is the customer's usage habit, which is no longer the traditional two-way link method. They can view the IP Camera Video and even control the PTZ of the IP Camera via the web page or PC-side PC software (UART AT commands).

8. Because of this model wireless link is a COFDM one-way link; there is no reverse data (only one-way transmission; data cannot be transmitted from the receiver to the transmitter); the customer can only watch the video of the IP Camera and cannot reversely configure the IP Camera's parameters or control the PTZ of the IPCamera.

9. This is a problem that many customers overlooked at first and later complained about after using it.

10. So we don't recommend that the client choose a one-way COFDM transmitter and receiver for the IP camera. We have a better solution for the IP Camera via two video link transceivers.

4. Could you please give me the Required C/N (BER=2x10-4 after Viterbi) for different the bandwidths 2, 4, 6, en 8 Mhz of HDMI video link we use?

1. Huidiglik, the receiver only provides two parameters of signal strength and bit error rate, and there is no C/N parameter

2. What parameters do you need to adjust according to different bandwidths? If it is a video code stream, the transmitter encoding board itself will automatically calculate the appropriate video stream code rate according to the currently used wireless parameters (bandwydte, GI, CR, ens), and the video code rate will be found after changing the bandwidth with the parameter board will automatically adapt.

cofdm video transmitter parameter configuare tool

3. vraag, If our camera quality is good enough for both 4 MHz and 8 MHz bandwydte. In hierdie geval, Should the customer choose 4 MHz of 8 MHz?

antwoord: Our one-way COFDM shipments use 4Mz wireless bandwidth by default, corresponding to a video bit rate of 3.12Mbps, which is enough for 1080p; If changed to 8MHz wireless bandwidth under the same conditions, the video bit rate doubles to 6.24Mbps. All customers can choose between wireless bandwidth 4MHz and 8MHz, even 6MHz can also be considered.

4. vraag: Which is better for this tx+rx set from a receive sensitivity view?

antwoord: For wireless links, it can be simply considered that the receiving sensitivity will be higher at lower wireless bandwidths. From the perspective of receiving sensitivity, 4MHz>6MHz>8MHz

5. What HDMI version is standard in Modulator input?

HDMI 1.4

6. Do you have any COFDM Relay Repeater Modules for the Wireless Video Transmitter and Receiver？

Sekerlik

Gaan asseblief die onderstaande skakel na

COFDM Relay Repeater module vir drone UAV draadlose videosender en ontvanger Vcan1870

COFDM Relay repeater for wireless video transmitter and receiver — COFDM-aflosherhaler vir draadlose videosender en -ontvanger

7. Could send me a data measurement of sensitivity for 4/6/8 MHz cases? Byvoorbeeld, for QPSK, 1/2CR, 1/32GI what threshold reception RX's input level (dBm)?

Single channel receiving sensitivity:

-97+/-1dBm at QPSK 8MHz,

-98+/-1dBm at QPSK 6MHZ,
Sensitivity increased by 3dbm when receiving with dual antennas

8. Does this module support over 1.4G? for example 2.4G, 3G, or 3.6G？

Ja, ondersteuning.

COFDM Video encoder modulator transmitter module 3.5G and 4G test result.

9. Waar kan ek die UDP-speler aflaai? Ons beveel Splayer_v4.2_2020.6.6 aan wat ons gereeld gebruik.

The receiver default firmware supports RTSP player, some clients prefer UDP player, which we also can offer, then RTSP player doesn't support. （RTSP and UDP can only choose one of the two firmware）

Laai asseblief af by die onderstaande skakel.

Splayer_v4.2_2020.6.6

https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing

Splayer_v4.3_2022.10.22

https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link

UDP Player: Splayer setting for living stream

10. Can you offer a metal box to protect the COFDM receiver board?

Sekerlik, kyk na onderstaande foto.

long range Wireless Video Transmitter and Receiver for Camera drone

Het nog 'n vraag?

Kontak ons asseblief vir meer inligting.

Stuur jou vraag

How to switch HDMI or CVBS video input via the UART AT command?

How to upgrade the COFDM video receiver

How to upgrade the COFDM drone video encoder modulator board

COFDM Wireless Video encoder modulator board delay low latency — COFDM Wireless Video encoder modulator board

resensies

Daar is nog geen resensies.

Wees die eerste om te hersien "COFDM Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Invoer AES 256 FHD RF-stroom” Kanseleer antwoord

107625

formaat	ATSD $(mimo), $(gi), $(Sentrale bedryfsfrekwensiepunt), $ (constellation), $(frek(KHz)), $(bw(KHz)), $(tx1_gain), $(tx2_gain)_ Voorbeeld: ATSD0,1,0,0,800000,8000,86.0,86.0_
parameter	One Antenna/Dual antenna mimo: 0 mimo disable; 1 mimo enable Guard Interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1/4 Convolution Code Rate: 0 1/2; 1 2 /3; 2 3/4; 3 5/6; 4 7/8; konstellasie: 0 QPSK; 1 QAM16; 2 QAM64; RCB Carrier Center Frequency(kHz) 200000~2700000(200MHz~2.7GHz, 1KHz-stap) RC900 Carrier center Frequency(kHz) 750000~930000(750MHz ~ 930MHz, 1KHz-stap) RCB Channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1KHz-stap) RCB Channel bandwidth bw(KHz) 2000~8000 (2MHz~8MHz, 1KHz-stap) Transmitting antenna 1 gain tx1_gain 0.0~89.75dB, 0.25dB stap Transmitting antenna 2 gain tx2_gain 0.0~89.75dB, 0.25dB stap
Terugkeerwaarde	soos:ATSD0,1,0,0,800000,8000,86.0,86.0_ SISO,GI: 1/16, CR:1/2, MOD: QPSK, frek:800000KHz,bw:8000KHz,tx1_gain:86.000000 tx2_gain:86.000000 OK
nota	Set command, save when power off. Different Bandwidths, Guard intervalle, Convolution code rates, Data rate calculation formulas corresponding to constellations Air interface rate Rate(Sentrale bedryfsfrekwensiepunt) Sentrale bedryfsfrekwensiepunt (bandwydte(MHz) * 8.0/7.0) / (1+GI) * 1512/2048Sentrale bedryfsfrekwensiepunt(Sentrale bedryfsfrekwensiepunt) Sentrale bedryfsfrekwensiepunt * 188/204. Taking 8MHz bandwidth as an example, different guard intervals, convolution code rates, data rates corresponding to constellations and required receiving signal-to-noise ratios $C:\Users\timyep\AppData\Roaming\Tencent\Users\157871537\QQ\WinTemp\RichOle\E0XEBCD_M4WD[M1BWR$}TK4.png$

27km 110km NLOS Vrae

warmste HDMI ultra lae latensie Vrae

Draadlose video-oordragmodule

AI SDK Module Board

DVB-T2-module

ISDB-T Module

HDMI-enkodeerderbord

Encoder Modulator Dekodeerder Demodulator Module Parameter Konfigurasie Instruksies COFDM AT Command

Update Record:

Suitable Models

Command Introduction

Command Classification

Command Details

Ping Command

Set Device Command

Set Gain Command

Set Modulation Mode command

Get Device Status Command

Set Encoder Command

Get Encoder Command

Get Input Command

Set Input Command

Set Output Command

Stel Invoerbronne-opdrag (skakel HDMI / CVBS insette)

Get User Command

Set Receiver Command

Get Receiver Command

Get Bit Error Rate Command

Set Password Command

Set Data Transfer Command

Get Data Transfer Command

Set IP Address Command

Get IP Address Command

OSD Overlay Protocol

Set Gain To Adjust

Get Gain To Adjust

Serial Port Utility software download

Vrae

1. How can I return to the No Password setting with 000000 indications after the change?

2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (wins) good for linear output operation? Or do you suggest some limited range for better linear operation?

3. I tried to set – B bandwidth (kHz) and E bit rate (Mbps). When I set E, the new value does not apply. So. the E setting is only for monitoring of available bitrate? if I wish to change the E (bitrate) I have to change only B (bandwydte)? Am I right?

COFDM Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Invoer AES 256 FHD RF-stroom

COFDM Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Invoer AES 256 FHD RF-stroom

Another side view

COFDM Encoder module, CVBS / HDMI insette, IP-uitset

COFDM Encoder module Advantage:

COFDM transmitter module

COFDM modulator-demodulator datasheet download

The last version of the TX RX board

Gereelde vrae

Het nog 'n vraag?

resensies

Wees die eerste om te hersien "COFDM Modulator Demodulator Module Encoder Decoder HDMI CVBS AV Invoer AES 256 FHD RF-stroom” Kanseleer antwoord

Verwante Produkte

Laat 'n antwoord Kanseleer antwoord

Ontdek meer van iVcan.com

Teken aan

registreer