HDMI To IP encoder modulator CVBS H.265 H.264 encoding board PCBA Ethernet RTSP UDP for UAV Drone Robotic
Tabla contenidos
Introducción
There are many HDMI encoding boards on the market. Have you met these problems?
- The delay is too long
- The encoding format cannot be customized
- UART AT remote control or operation cannot be used.
- Can not support HDMI and CVBS dual video input encoding
Le placa codificadora soporta HDMI, Sdi, Yaan tu vídeo CVBS, ka Salida flujo kuxa'an IP ethernet RJ45, most applications are for wireless video transmitters, Ba'ax u codificar le señal vídeo HDMI wa CVBS ti' le secuencia viva digital yo'osal H.264 wa H.265, ka transfiéralo le receptor, Convertidor u CVBS u IP.
The HDMI and Composite CVBS video to IP ethernet stream encoder modulator module board parameter can be configured by UART software modification. Búukint u ti' máax ku To'one' wa K'abéet personalizar jump'éel función similar utia'al u satisfacer u tsol.
Ventaja:
Ultra-Low Latency
H265 or H264 support
HDMI and CVBS Dual Encoding
Two Audio inputs can switch
Interfaz usuario web o serial port UART AT command configuration management
- Ultra-low latency H.265/H.264 audio and video encoding maximum support 1080P60 real-time video capture and encoding
- The HDMI or AV input is encoded and outputted to a wireless module through the Ethernet port. The video encoding bit rate can be adjusted dynamically.
- Admite entrada u audio ka salida u decodificación audio. (Remote operate by UART AT command choose HDMI or CVBS audio)
- You can choose between HDMI or AV encoding for two videos with the option to control the input source using an AT command.
Característica
Le placa implementa codificación compresión audio yéetel vídeo H.265 leti' H.264, admite codificación tak 1080P u 60fps, and is backward compatible with other resolutions and frame rate encoding.
Yaan u audio yéetel vídeo
- Interfaz HDMI(audio+video):1080 60P'EL,1080 50P'EL,1080 30P'EL,1080 25P'EL,1080 60In,1080 50In, 720 60P'EL,720 50P'EL,720 30P'EL, …, ya'ab modos adaptativos (1080p'el, 1080in, 720p'el, 1024×768, 1280×1024);
- AV in the interface (Audio + video):720×480 60In(NTSC),720×576 50In(PAL), modo adaptativo. through the AV interface, it can be Line in Mic in.
- Yaan tu jool audio predeterminada le le ti' jump'éelili' kuchil-u le interfaz yaan tu vídeo.
- The audio input interface can also be configured through the Web UI when the serial port detects audio.
- The audio and video source signals are encoded, yéetel le interfaz kaambal ti' fuentes audio yéetel vídeo xan ku páajtal configurar ti' le puerto serie configuración.
- The audio and video source acquisition interface can be dynamically switched through serial port commands during system operation.
Codificación vídeo: Formato H.265 wa H.264, U páajtal u configurar le velocidad bits codificación.
Codificación audio: Codificación AAC. - Yo'osal le programación firmware yaabilajech HDMI + AV le captura yéetel codificación simultánea u tíip'ik audio le placa(Salida audio)
- Le placa yaan ti' jump'éel función salida decodificación u audio incorporada(Salida internet ichil), Ba'ax ku páajtal conectar ti' jump'éel auricular externo wa amplificador potencia audio. Le audio ku decodifica yéetel u reproduce.
Puerto Ethernet (Interfaz Ethernet)
supports our two-way wireless transmission modulator module, jump'éel uláak' K'aanan bidireccionales u terceros.
Interfaz yaantal inalámbrica( FPC Main interface)
U páajtal conectar ti' k xook yaantal inalámbrica COFDM, yéetel xan u páajtal conectar ti' k xook enlace yaantal inalámbrica bidireccional.
Datos-UART
Nivel TTL 3.3V, U páajtal configurar parámetros bey le velocidad ti' baudios yaantal. Le ken u placa le ti' jump'éel enlace inalámbrico, Le puerto serie datos ku meyajtiko'ob utia'al u yaantal transparente u datos.
Control-UART
Nivel TTL 3.3V, Ba'ax ku páajtal conectar ti' k panel configuración u parámetros jump'éel uláak' nu'ukulil superior utia'al u configurar le yaan u placa codificación.
Interfaz de host USB
ka' yéetel mantenimiento software. (optional USB recorder function)
Tensión alimentación
admite protección conexión inversa u jool le sajkabo' alimentación, and supports the power input range of 7~30V. Proporciona jump'éel interfaz salida potencia 5V. Le jant p'áatalij máximo u energía u meyaj le 2.4W (1080Codificación P60 H.265), yéetel le sáasilo' wóolis jach u 200mA.
Indicador u
indicador potencia, indicador meyaj codificación vídeo.
The HDMI to IP encoder board size Jach 70x45x1.2mm (LWH)
Le ka'anilo' le componente posterior le inferior u 2,5 mm, yéetel le ka'anilo' le componente frontal inferior ti' 6,8 mm.
Peso le tabla
20.6 gramos.
Señal interfaz
- TI' LE (Audio in left), beel ts'íik lela' yaan tu audio;
-
AR(Audio le derecha), beel k'abil ti' yaan tu audio;
-
UK' U LU'UM, señal lu'um;
-
T.U.M PESOS AMERICANO, Yaan tu vídeo analógica. (Please ignore the color of the wiring, make sure the fourth jack is CVBS Composite video input.)
Control UART: Equipado yéetel puerto serie,4Pin 1.25mm pitch socket, Nivel TTL 3.3V, utilizado utia'al u configuración le parámetro placa, u páajtal conectar ti' le panel configuración ti' parámetros Sihaida jump'éel uláak' nu'ukulil host.
Interfaz USB:4Pin 1.25mm pitch socket, used for the encoder board software upgrade and maintenance.
Interfaz salida audio:2Pin 1.25mm pitch socket, Le placa yaan ti' jump'éel función salida decodificación u audio integrada(Salida internet ichil), Ba'ax ku páajtal conectar ti' jump'éel auricular externo wa amplificador potencia audio. Decodificar ka reproducir yaan tu audio jool tak le puerto páawo'ob.
Ethernet: Interfaz Ethernet,4Pin 1.25mm pitch socket
Ka'anatako'ob
- Done or UAV video encoding
- Robotic or mini-control vehicle
- Unmanned Vehicles UAV
- Unmanned Submarine
- The HDMI to IP board can be COFDM modulation module RCB stacked and assembled with a COFDM one-way transmission module. The connection interface is FPC Main (26Interfaz cable plano PIN flexible). HDMI+AV encoder + COFDM Transmitter Module
- The HDMI to IP encoder board PCBA is connected to a two-way wireless link through the network port. Ti' le súutuka', Le parámetros funcionamiento ku páajtal configurar ti' le interfaz usuario u Web le puerto páawo'ob. Je'ebix., Establecer velocidad bits codificación vídeo, Método codificación H264 leti' H265, método yaan tu audio, velocidad tu baudios le puerto serie, etcetera.
- The board can be connected to the Control-UART parameter configuration panel to set operating parameters.
- Versión le interfaz HDMI: HDMI V1.4
- Velocidad de datos de salida Ethernet: 100Mbps
- Rango temperatura funcionamiento: -40~85 grados
- T.u.m operativo u compatible: Linux integrado
Web UI management Parameter setting
K'áat chi'oba' Frecuentes
Le placa codificación vídeo IP HDMI u yil le configuración parámetros ma'alo'ob ti' le interfaz usuario u web le puerto páawo'ob ka modificar le de acuerdo con kajtalo'ob ichil u ka'anatako'ob. ti' le explorador puertos páawo'ob http://192.168.1.30/ (le dirección IP ti' le placa codificación)
1. Compruebe le interfaz usuario web tak le navegador, ti' le wíimbala' u kaambal, Wa yaan u fuente vídeo Jach ma'alob, then it will show the CVBS or HDMI at the red arrow.
2. Compruebe u le sáasilo' LED placa codificación HDMI parpadee wa ma'.
Wa ya'ax yéetel parpadea, Tu continuación le fuente yaan tu vídeo u yutsil., Wa ma' parpadea, then please check the video input source is ok or not.
Le tasa bits codificación u je'el configurar. Le servidor web predeterminado ku je'ets'el ti' 0.0 utia'al representar kiis (3.12Mbps u utilizará internamente). Le clientes táan u béeytal u modificar le ku. Je'ebix., Jach páajtal configurar 1Mbps ~ 2Mbps wa incluso menos.
1. Large I-frames are prone to frame loss due to wireless transmission;
2. If the gop setting is large, the loss of the I frame will lead to a longer recovery time after the blurred screen;
3. The size difference between I frame and P frame is large, which will increase the transmission delay.
1、比如相机输入1080p60,那gop设置为60/120/180(不建议设置太大)
2、比如相机输入1080p25,那gop设置为25/50/75(不建议设置太大)
3、比如相机输入1080i60,由于需要去交织,所有实际编码是1080p30,那gop设置为30/60/90
从上面可以看到,由于输入相机帧率不确定,所以我们一般建议配置0(Chéen tu juuna)
cvbs分制式,pal是25fps,ntsc是30fps
假设是pal,那gop设置25/50/75
1、大的I帧容易因为无线传输的原因导致丢帧花屏;
2、gop设置大,I帧丢失导致花屏后恢复时间变长;
3、I帧和P帧大小差别大,会增加传输延迟
Please download at the below link.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
- We can modify the TS stream over UDP, but the TS stream is a non-standard TS stream that we have modified, which needs to be interpreted by our decoder board or special player (Descargar).
- If you agree with the RTSP protocol, VLC can play it; if you only agree with the TS stream (due to our non-standard modification), VLC cannot decode and play it, so we must use our special player. (Descargar).
- If you want to switch to the standard MPEG-2 TS stream to play with VLC, our software engineer can customize the firmware for you (this will take a few days) for an additional fee of USD500.
- We use non-standard mpeg-2 ts streams primarily for the following reasons:
- The standard mpeg-2 ts stream has too much overhead outside the effective data, making it unsuitable for use with cofdm;
- The standard mpeg-2 ts stream is difficult to implement the aes encryption function;
- The standard mpeg-2 ts stream is difficult to achieve serial port transparent transmission (used with our decoder board)
- If you don't need our decoder board, encryption and serial port transparent transmission, it is also possible to use standard mpeg-2 ts stream
- It is recommended that you try our player; in real-time performance, our player outperforms vlc.
The vlc player's algorithm does not take into account real-time performance; Ichil u kúuchil le jeelea', it will constantly adjust its cache (only increase but not shrink). Bix resultado, the longer it is played, the longer the delay may be (especially when used with a wireless link)
1. SSL certificate is HTTPS protocol, our products do not support it now, only HTTP.
2. The default encoder board through the RTSP protocol, RTSP is not encrypted. You can set a longer password. And change it frequently.
3. If you want to encrypt, you need to use a pair of our codec boards (with encoder and decoder board as TX and RX), with UDP protocol, and they are using aes256 encryption. (Just like the bank level.)
Je'el, Yantio', Béet contáctenos. Let me list your demand at the below.
1. We need to take a composite analog PAL video signal and transmit it using h264 over MPEG2 TS. Ma'alo'ob
2. The output must be playable through VLC. Ma'alo'ob
3. UPD://@1030. Ma'alo'ob
4. The output network stream packet should be 188 bytes standard mpeg2 TS. Ma'alo'ob
5. Compression scheme is h. 264, CVBS PAL input and IP output. Ma'alo'ob
Yantio'
Much consulte le uláak' enlace
COFDM UART AT command for the transmitter and Receiver.
wa
Descargue le archivo COFDM Transmitter UART AT command PDF.
Please follow the checkpoints below to confirm.
- After connecting the encoder board with your computer by ethernet cable, the LED of RJ45 connector should be blinking or not. (to check the ethernet connection is ok or not)
- Is your computer configured with 192.168.1.x network segment ip?
- Have you modified the default IP address of the encoding board? If the IP address changed, maybe you can download and use the below software to find what IP address now.
- Or Directly connect the UART cable of the encoding board ti' le computadora, and use the serial port debugging assistant to send the ATGIP_ command.get ip address command Operation Video at Youtube
formato
ATGIP_
Ejemplo: ATGIP_
Parámetro
Ma'
Búukinta'al
to query the current IP address of the receiving end
Return value
Ejemplo:
ATGIP_
ATGIP192.168.0.215 OK
Observación
- query command
- More COFDM UART AT commands, Much consulte le enlace. https://ivcan.com/encoder-modulator-decoder-demodulator-module-parameter/
These parameters are determined by the camera, only the sensor has it.
One more question: In the future is there any possibility to incorporate these features in the output side of encoder (if we get volume orders) ?
Our Answer: These are the parameters of the isp, and our current encoding boards are all bypass isp (because we don't connect the sensor, we don't need and can't use the isp), so we can't add these parameters.
Je'el, CVBS input support NTSC and PAL, Automatic detection and adaptation
- le parameter configuration board tool is mainly used for the COFDM module function. If you buy this HDMI / CVBS to IP encoder Vcan1746 separately, you don’t need to buy a parameter configuration board tool, you can adjust the parameters through the Web UI.
- Je'ele', if you want to use the parameter configuration board tool to adjust some parameters of the encoder board, it is also possible.
- Je'ebix., the video encoding bit rate can be configured through the Web UI or changed through the extra parameter configuration board tool. The Web UI can configure all the parameters, and the parameter configuration board tool can only adjust some of them.
Ma'alo'ob, Much consulte le uláak' enlace
Je'el, Wa ka k'abéet a, we can offer you the special firmware to have USB recorder function.
K'áat chi': Does your USB DVR support playback on the encoded video?
Núukik: Ma', The USB has the record function. You need to play it on a computer, it can not playback on the encoder board directly.
- Do you mean HDMI or AV input, or do you need HDMI and AV to support two simultaneous inputs?
- Currently it supports either HDMI or AV input.
-
Vcan1746 can only choose one of HDMI/AV at present, other boards can meet the firmware you need, but this board only supports SDI + AV/AHD output.
-
If necessary, you can evaluate the board with SDI + AV/AHD input to see if it meets your requirements. Tu óoltaj afirmativo, our HDMI + AV input Vcan1746 can be made the same later.
-
If you really need to evaluate the HDMI + Interfaz AV, please first buy Vcan746 and burn the default shipping firmware for testing. HDMI and AV can be selected for use. If there is a certain amount of follow-up orders, we can develop a special firmware to support HDMI+AV input at the same time.
-
The display of HDMI and CVBS video input by two channels at the same time is similar to Hikvision IPC, which is divided into main bit rate and sub bit stream. The main stream corresponds to HDMI, and the sub stream corresponds to CVBS.
- Now we can develop a new firmware to support HDMI and CVBS to live streaming at the same time, but the audio can only be selected from one of the two (the system selects HDMI audio/analog audio according to the video access situation).
Supported.
Our HDMI and CVBS input video encoding board has a USB interface, which can be used for USB recording. It can also be used as the input interface of a USB web camera.
K'ajlayo', our video encoding board can convert the signal of your USB web camera into a network interface, while supporting ultra-low latency and supporting h264 and h265 encoding.
Láayli' teen jump'éel k'áat chi'?
Búukint u ti' máax ku To'one' tia'al a wojeltik.
Túuxta'al a k'áat chi'
HDMI Video Sources Input IP Ethernet Output encoder, VLC RTSP operation
Industrial-grade temperature range from -40°C to 70°C Celsius test
Support HDMI and CVBS 2 video streams at the same time
How to get the IP address of the encoder back if you forget
Asab k'áat chi'oba' frecuentes
HS Code
8517629900, Some of our customers use this HS code for your reference.
Special Function Custom Development
-
HDMI and CVBS Dual Video Encoding
-
USB has a video recording function.
-
Special handling of encoding formats to match your custom decoder board
скачать видеокодер