àlẹmọ

Composite CVBS video to IP ethernet converter encoder board mini Video Encoder Board CVBS input and IP Ethernet output

CVBS to IP converter, Smallest AV input Encoder board to ethernet output, composite video audio, or camera to IP transform

SKU: Vcan1987 Ẹka: TX RX Modulu Tags: CVBS to IP converter, ultra low latency encoder board

Apejuwe
Fi ibeere ranṣẹ

CVBS to IP converter, Smallest AV input Encoder board to ethernet output, composite video audio, or camera to IP transform

Atọka akoonu

iṣẹ

CVBS to IP converter AV encoding board function:

Analog audio and video input, H264 aiyipada, output through the network port IP ethernet.

Composite CVBS video to IP ethernet converter encoder board
mini Video Encoder Board CVBS input and IP Ethernet output
Support UDP RTSP player VLC
Analogue camera to internet ONVIF TCP IP

Ibeere ọfẹ, Ọrọ ọfẹ, Atilẹyin ọfẹ, Ifihan apẹẹrẹ ọfẹ .

ni wiwo

CVBS to IP converter Refer to the figure above for the encoding module interface and interface signals. The interface description is as follows:

Afọwọṣe iwe ohun ati awọn fidio input ni wiwo: support analog video input, and audio input(Line ni Way)。
Input signal interface(1.25mm spacer) ati 13 PIN Toshiba FPC Cable socket multiplexing;
Network ibudo: 4PIN 1.25mm spacing base, the base signal, ati awọn13 PIN Toshiba FPC Cable Socket multiplexing;
Software protocol: UDP way output.

13Pin Toshiba FPC Pin Define

CVBS to IP converter Smallest AV input Encoder board to ethernet output, composite video audio camera to IP transform

13PIN FPC socket layout enlarged pad diagram

Ni lilo gangan, you can put off the expansion interface card on the right side of the mini AV board to meet the needs of the structure.

USB ni wiwo: Write board firmware, the 4Pin 1.25mm spacing seat can be removed when the structure is installed.

Matching serial port:

4Pin 1.25mm spacing seat, which can connect to our parameter configuration panel board to configure the H264 encoding code rate and other parameters. Fun alaye, please refer to the operation description of our parameter configuration panel.

After you change the parameters well, you do not need to change and adapt to the needs of the structure, you can remove the 4-pin seat.

Iṣagbewọle agbara: 2-pin welding hole, support input voltage range 6 ~ 15V.

CVBS to IP converter board size: 42x37x1.2mm.

The thickness of the board PCB is 1.2mm, the thickness of the maximum device on the back is less than 2mm, and the thickness of the highest front device on the front is less than 5.5mm.

Heating:

The maximum power consumption of the CVBS to IP converter encoding module is 150mA@12V.

The normal operating temperature range is 0 ℃ ~ 55 ℃ (degrees Celsius).

If it is placed in a small structure for operation for a long time, the CPU needs to be cooled.

CVBS to IP converter Smallest AV input Encoder board to ethernet output, composite video audio, or camera to IP transform

FAQs

1. Does it support my low-resolution thermal camera 256x192 on CVBS video?

CVBS currently only supports the common PAL (720x576) ati NTSC (720x480) resolutions.
Because the interface chip automatically adapts, We guess that our encoder board can not recognize your interface chip with this resolution.
It is recommended that you connect the thermal imaging camera to an AV monitor or HDMI monitor to see if it can be displayed. If so, although the actual resolution is low, the video stream format may not be this 256x192.
If it's HDMI, it's possible to modify the software to adapt to your camera; if it's CVBS, I think it's difficult unless you send the camera over and we can debug the software.
If you need a suitable IR thermal imaging camera, please check our product.