SNM401 Ad Hoc Network Module

1. නිෂ්පාදනය විස්තරය

SNM401 Centerless Ad Hoc Network Module realizes centerless long-distance communication between modules, and adopts the world’s latest LDPC encoding and decoding technology, compared to the RS level used by traditional radio stations The concatenated convolutional code can have a coding gain of 5dB, and at the same time, through the “self-relay wireless communication” තාක්ෂණ, it innovatively realizes automatic relay between modules, thereby greatly improving the coverage effect and transmission distance. SNM401 adopts ad-hoc network wireless communication technology, any node can receive and process the same signal forwarded by multiple nodes at the same time, combine these signals forwarded from different nodes, demodulate the original information to the greatest extent possible, and have a larger transmission distance and higher transmission reliability. The wireless communication technology of the ad hoc network does not require routing, and multiple nodes automatically determine whether to start the forwarding according to the received signal quality and field strength, and the relay is upgraded from a multi-hop single-point relay to a multi-hop multi-point relay. The state relay is upgraded to a mesh relay. When any node in the relay network is disconnected from the network, other relay lines in the relay network work normally so that the relay effect is not affected.

2. නිෂ්පාදන විශේෂාංග

◆Operating frequency: 400-500MHz වලින්

◆Single-hop transmission distance: 3～5Km

◆Dynamic topology convergence: 1මෙනෙවිය

◆Transmit power: 1W

◆Receive sensitivity: -127dBm

◆Working voltage: 3.5-4.5V

◆Signal to noise ratio Threshold: 1dB ට

◆Channel spacing: 12.5kHz

◆Frequency stability: 1ppm

◆Intermodulation: 65dB ට

◆Encryption: 256AES

◆Spurious response immunity: 75dB ට

◆Adjacent channel selectivity: 65[email protected]

◆Operating temperature: -40～ +85℃

◆Module size: 33.5X42X3.4mm

3. අයදුම්පත

◆Internet of Things ◆Individual Soldier System ◆Emergency Broadcasting

◆UAV ◆Real-time Remote Control ◆Digital Intercom

◆Emergency Communication ◆Robot ◆Wireless Data Transmission

4. Working Parameters

Table 1: Operating Parameters Table

පරාමිතිය	කොන්දේසි	අවම	සාමාන්ය	උපරිම	ඒකකය
Operating Frequency Band		400		500	MHz වලින්
මෙහෙයුම් උෂ්ණත්වය		-40	25	+85	℃
මෙහෙයුම් වෝල්ටීයතා		3.5	4	4.5	V
Transmitting Power			30		dBm
සංවේදීතාව ලබා ගැනීම		-130	-127	-125	dBm
Maximum RF Input Power				+33	dBm
අනුක්‍රමික වරාය බෝඩ් අනුපාතය			115200		bps
sleep current	@ EN=0		40		uA
receive current			160		mA
transmit instantaneous current	@VCC==4V, 1W			1800	mA
transmit average current	@VCC==4V, 1W		600		mA
audio input voltage				1.5	VPP
audio output Impedance			150		ඕම්

සටහන: If the working conditions of the module exceed the above limit values, එය මොඩියුලයට ස්ථිර හානියක් විය හැක.

5. Module pins and definitions

Figure 1 SNM401 Pin Diagram

Abbreviation	විස්තර
AI	Analog input
AO	Analog output
AIO	Analog bi-direction
DI	Digital input
DO	Digital output
DIO	Digital bi-direction
පී	බලය
ජී	භූමිය

Table 3 SNM401 pin definition

Pin NO	Pin name	වර්ගය	විස්තර
1	GND	ජී	GND
2	කූඹියා	AIO	antenna port
3	GND	ජී	GND
4	GND	ජී	GND
5	VBAT	පී	External 3.5V-4.5V battery or power supply, 4V is recommended
6	VBAT	පී
7	GND	ජී	GND
8	GND	ජී	GND
9	TX_STATE	DO	module transmit indication Signal, the high level is transmitting
10	RX_STATE	DO	module receiving indication signal, the high level is receiving
11	එන්.සී.		No connect
12	එන්.සී.		No connect
13	GND	ජී	GND
14	TXD	DO	serial port data transmitting pin
15	RXD	DI	serial port data receiving pin
16	SET	DI	module Serial port configuration signal, configure parameters when high level, send and receive data when low level
17	EN	DI	module open enable signal, high level open, low level close
18	GND	ජී	GND
19	PRO1	DIO	programmable definition pin
20	PRO2	DIO	programmable Definition pin

: The module is regulated by 3.3V LDO inside, and all digital IOs are 3.3V level.

 

6. පැකේජය තරම

Figure 2 SNM401 size chart

Figure 3 SNM401 package Figure

7. LAYOUT precautions

1.එමSNM401 module works at 400-500MHz වලින්and the influence of various factors on wireless transceivers should be avoided.

2. It is laid under the module GND, and the traces are extended to the periphery as far as possible.
3. It is recommended to use insulating material to isolate the module mounting position on the substrate, උදාහරණයක් වශයෙන්, place a whole piece of in this position

silkscreen

4. Try to take a short and thick power line to the module, the recommended copper line width is80mil, and the decoupling capacitor should be placed as close to the power pin as possible.

8. Software configuration

8.1 Parameter configuration

Users can obtain and configure parameters through the serial port, the serial port baud rate ය 115200, the data bit is 8ටිකක්, the stop bit is 1ටිකක්, and there is no parity bit.

Table 4 Serial port packet format

Serial port table packet
identification word	දිග	Command	instruction reply/reply content
1Byte	1Byte	1Byte	NByte

8.1.1 Identification word

The identification word is fixed as 0x68.

8.1.2 දිග

දිග COFDM රැහැන් රහිත සම්ප්‍රේෂණ පද්ධති සම්ප්‍රේෂණ අනුපාතය ගණනය කිරීම විධානය + command content/reply content.

8.1.3 Command

සියලුම මාදිලියේ ස්ථාපනය සඳහා සුදුසු වේ 5 Serial Command-List

කාර්යයන්	Command	අන්තර්ගත	Reply Content
Acquire RF Parameters	0x00	නැත	සංඛ්යාත(4Byte) +බලය(1Byte) +වින්යාස තත්ත්වය(1Byte) +Noise(2Byte) +Baseband Version Number(1Byte)
Set RF Parameter	0x01	සංඛ්යාත(4Byte) +බලය(1Byte)	නැත
data relay level	0x0C	නැත	data relay level(1Byte)
Set data relay level	0x0D	Data relay level(1Byte)	නැත
key to acquire	0x0E	නැත	key(32Byte)
set key	0x0F	key(32Byte)	නැත
get module version	0x12	නැත	module name + version number
module ready	0x55	නැත	නැත
save configuration	0x66	නැත	නැත
data receive	0xA2	නැත	transparent data (NByte)
data send	0xB2	transparent data (NByte)	නැත

8.1.4 Instruction content/reply content

8.1.4.1 Obtaining RF parameters

සංඛ්යාත: The unit is Hz, the setting range is ~5000000000, and the precision is 500HHz.

බලය:1-high power 1W,0-low power 0.5W, the default is high power 1W.

Configuration status: Indicates the radio configuration status,0-uninitialized,1-configuring,2-configured successfully.

Noise Floor: Indicates the current frequency noise intensity, කුමන 2 is meaningful

Baseband version number: The upper 4 බිටු represent the major version number, and the lower 4 බිටු represent the minor version number.

Configuration Packet:0x68 0x01 0x00

Return Packet:0x68 0x0A 0x00 Frequency Power Configuration Status Noise Floor Baseband Version No.

8.1.4.2 Setting RF Parameters

After configuring RF parameters, you must wait for the successful configuration (පිළිබඳ 2 තත්පර) before the module can enter the setting work correctly state.

Configuration package:0x68 0x06 0x01 Frequency power

return package:0x68 0x01 0x01

8.1.4.3 Obtaining data relay level

SH ad hoc network technology is a simulcast mesh relay method, which does not require routing, which can greatly improve the coverage.number of relay hops එන් refers to the number of hops that can be relayed during data transmission, and the maximum number of relay hops is 16. With each additional hop, the transmission distance doubles, but the transmission time increases accordingly, as shown in the table below.

Table 6 Comparison of Relay Levels

Relay Hops	Transmission Bytes	Transmission Time
එන්	<36	N*50ms
එන්	37-72	N*100ms
එන්	73-108	N*150ms
එන්	109-144	*200මෙනෙවිය
එන්	145-180	N*250ms
එන්	181-216	N*300ms
එන්	217-252	N*350ms
එන්	253-288	N*400ms

Configuration package: 0x68 0x01 0x0C

Return package: 0x68 0x02 0x0C Data relay level

8.1.4.4 Set data relay level

Configuration package:0x68 0x02 0x0D Data relay level

return packet:0x68 0x01 0x0D

8.1.4.5 Obtain the key

key for communication encryption, the module will automatically discard the voice information and data information whose key is inconsistent with its own key, and the key is all 0.

Configuration Packet:0x68 0x01 0x0E

Return Packet:0x68 0x21 0x0E යතුර

8.1.4.6 Set Key

Configuration Packet:0x68 0x21 0x0F යතුර

Return Packet:0x68 0x01 0x0F

8.1.4.7 Get Module Version

Configuration Packet:0x68 0x01 0x12

Return Packet:0x68 0x15 0x12 0x53 0x69 0x6d 0x75 0x6c 0x48 0x6f 0x63 0x32 0x31 0x38 0x5f 0x31 0x31 0x30 0x2e 0x30 0x00 ය“Simulhoc2618_V1.0.0”

8.1.4.8 මොඩියුලය

Return package:0x68 0x01 0x55

8.1.4.9 Save configuration

command to save all settings to සැණෙළිය, and the saved configuration will be used directly after power-on.

Configuration package:0x68 0x01 0x66

Return package:0x68 0x01 0x66

8.1.4.10 Data reception

When the SET pin is low, the module will transparently transmit the received data package to the user. The length varies according to the actual transparent transmission data length.

Return package:0x68 දිග 0xA2 විනිවිද පෙනෙන

8.1.4.11 දත්ත සම්ප්රේෂණය

Only when the SET pin is at a low level can data be transmitted, and the data sent in a single transmission does not exceed 36 බයිට්. The length varies according to the actual transparent transmission data length. If a return packet is received, it indicates that the data transmission failed this time.

Configuration package: 0x68 Length 0xB2 Transparent data

return package: 0x68 0x01 0xB