HDMI til IP-kodermodulator CVBS H.265 H.264 kodingskort pcba Ethernet RSTP UDP for UAV Drone Robotic
$399.00
HDMI To IP encoder modulator CVBS H.265 H.264 encoding board PCBA Ethernet RTSP UDP for UAV Drone Robotic
Innholdsfortegnelse
Introduksjon
There are many HDMI encoding boards on the market. Have you met these problems?
- The delay is too long
- The encoding format cannot be customized
- UART AT remote control or operation cannot be used.
- Can not support HDMI and CVBS dual video input encoding
Dette koderkortet støtter HDMI, SDI, CVBS video input, og IP ethernet RJ45 live stream-utgang, most applications are for wireless video transmitters, which can encode the HDMI or CVBS video signal to the digital living stream by H.264 eller H.265, og overføre den til mottakeren, CVBS til IP-omformer.
The HDMI and Composite CVBS video to IP ethernet stream encoder modulator module board parameter can be configured by UART software modification. Ta kontakt med oss hvis du trenger å tilpasse en lignende funksjon for å møte ditt prosjekt.
Fordel:
Ultra-Low Latency
H265 or H264 support
HDMI and CVBS Dual Encoding
Two Audio inputs can switch
Web UI eller serial port UART AT command configuration management
- Ultra-low latency H.265/H.264 audio and video encoding maximum support 1080P60 real-time video capture and encoding
- The HDMI or AV input is encoded and outputted to a wireless module through the Ethernet port. The video encoding bit rate can be adjusted dynamically.
- Støtte lydinngang og audio dekoding utgang. (Remote operate by UART AT command choose HDMI or CVBS audio)
- You can choose between HDMI or AV encoding for two videos with the option to control the input source using an AT command.
Trekk
Brettet implementerer H.265/H.264 lyd- og videokomprimeringskoding, støtter opp til 1080P @ 60 bilder per sekund koding, and is backward compatible with other resolutions and frame rate encoding.
Lyd- og videoinngang
- HDMI-grensesnitt(lyd+video):1080 60P,1080 50P,1080 30P,1080 25P,1080 60Jeg,1080 50Jeg, 720 60P,720 50P,720 30P, …, ulike modi adaptive (1080p, 1080Jeg, 720p, 1024×768, 1280×1024);
- AV in the interface (lyd + video):720×480 60Jeg(NTSC),720×576 50Jeg(PAL), modus adaptive. through the AV interface, it can be Line in Mic in.
- Standard lydinngang er det samme som videoinngang grensesnitt.
- The audio input interface can also be configured through the Web UI when the serial port detects audio.
- The audio and video source signals are encoded, og lyd- og videokildeanskaffelsesgrensesnittet kan også konfigureres gjennom konfigurasjonsserieporten.
- The audio and video source acquisition interface can be dynamically switched through serial port commands during system operation.
videokoding: H.265 eller H.264-format, kodingsbithastigheten kan konfigureres.
Lydkoding: AAC-koding. - Ved å programmere spesiell fastvare HDMI+AV samtidig fangst og koding av kortets lydutgang(Lyd ut)
- Brettet har en innebygd lyddekodingsutgangsfunksjon(Linje ut), som kan kobles til en ekstern hodetelefon eller lydeffektforsterker. Lyden dekodes og spilles av.
Ethernet-port (Ethernet-grensesnitt)
supports our two-way wireless transmission modulator module, eller andre tredjeparts toveiskoblinger.
Trådløs overføring grensesnitt( FPC Main interface)
kan kobles til vår COFDM trådløse overføringsmodul, og kan også kobles til vår toveis trådløse overføringslinkmodul.
Data-UART
TTL 3.3V nivå, parametere som overføringshastighet kan konfigureres. Når brettet er gjennom en trådløs kobling, dataserieporten brukes for transparent dataoverføring.
Control-UART
TTL 3.3V nivå, som kan kobles til vårt parameterkonfigurasjonspanel eller en annen øvre datamaskin for å konfigurere kodekortsystemet.
USB Host-grensesnitt
programvareoppgradering og vedlikehold. (optional USB recorder function)
Forsyningsspenningen
støtter omvendt tilkoblingsbeskyttelse av strøminngangen, and supports the power input range of 7valgfri avstandskarakter. Gir et 5V strømutgangsgrensesnitt. Maksimalt strømforbruk er 2,4W (1080P60 H.265 koding), og maksimal strøm er 200mA.
indikator
Strømindikator, arbeidsindikator for videokoding.
The HDMI to IP encoder board size er 70x45x1.2mm (LWH)
Høyden på bakdelen er mindre enn 2,5 mm, og høyden på frontkomponenten er mindre enn 6,8 mm.
Board vekt
20.6 gram.
Grensesnittsignal
- AL (Audio in left), lydinngang venstre kanal;
-
AR(Lyd til høyre), lydinngang høyre kanal;
-
GND, signaljord;
-
AV, analoge videoinngang. (Please ignore the color of the wiring, make sure the fourth jack is CVBS Composite video input.)
- HDMI to IP encoder modulator CVBS H.265 H.264 encoding board pcba Ethernet LAN HTTP RTSP UDP onvif TCP IP interface signal 2
Kontroller UART: Utstyrt med seriell port,4PIN 1,25 mm stikkontakt, TTL 3.3V nivå, brukes for konfigurasjonen av tavleparameteren, kan kobles til Sihaida parameter konfigurasjonspanel eller en annen vertsdatamaskin.
USB-grensesnitt:4PIN 1,25 mm stikkontakt, used for the encoder board software upgrade and maintenance.
Lyd ut grensesnitt:2PIN 1,25 mm stikkontakt, brettet har en innebygd lyddekodingsutgangsfunksjon(Linje ut), som kan kobles til en ekstern hodetelefon eller lydeffektforsterker. Dekod og spill av lydinngangen fra nettverksporten.
Ethernet: Ethernet-grensesnitt,4PIN 1,25 mm stikkontakt
applikasjon
- Done or UAV video encoding
- Robotic or mini-control vehicle
- Unmanned Vehicles UAV
- Unmanned Submarine
- The HDMI to IP board can be COFDM modulation module RCB stacked and assembled with a COFDM one-way transmission module. The connection interface is FPC Main (26PIN flat kabel fleksibelt kabelgrensesnitt). HDMI+AV encoder + COFDM Transmitter Module
- The HDMI to IP encoder board PCBA is connected to a two-way wireless link through the network port. På denne tiden, driftsparametrene kan konfigureres via nettverksportens web-UI. For eksempel, angi bithastigheten for videokoding, H264/H265-kodingsmetode, lydinndatametode, seriell port baudrate, etc.
- The board can be connected to the Control-UART parameter configuration panel to set operating parameters.
- HDMI-grensesnittversjon: HDMI V1.4
- Ethernet-utgang Datahastighet: 100COFDM trådløs overføringssystem beregning av overføringshastighet
- Driftstemperaturområde: -40~85 grader
- Kompatibelt operativsystem: Innebygd Linux
Web UI management Parameter setting
Vanlige spørsmål
Dette HDMI-video til IP-kodingskortet kan se gjeldende parameterkonfigurasjon gjennom nettverksporten Web UI og endre det i henhold til applikasjonsbehov. gjennom nettleseren for nettverksport http://192.168.1.30/ (IP-adressen til kodingskortet)
1. Vennligst sjekk nettgrensesnittet fra nettleseren, på bildet under, hvis videokildeinngangen er ok, then it will show the CVBS or HDMI at the red arrow.
2. Kontroller at LED-lyset for HDMI-kodingskort blinker eller ikke.
Hvis den er grønn og blinker, da fungerer videoinngangskilden bra, hvis ikke blinke, then please check the video input source is ok or not.
The encoding bitrate can be configured. The default web server is set to 0.0 to represent auto (3.12Mbps will be used internally). Customers can modify this value. For eksempel, it is possible to configure 1Mbps~2Mbps or even lower.
1. Large I-frames are prone to frame loss due to wireless transmission;
2. If the gop setting is large, the loss of the I frame will lead to a longer recovery time after the blurred screen;
3. The size difference between I frame and P frame is large, which will increase the transmission delay.
1、比如相机输入1080p60，那gop设置为60/120/180(不建议设置太大)
2、比如相机输入1080p25，那gop设置为25/50/75(不建议设置太大)
3、比如相机输入1080i60，由于需要去交织，所有实际编码是1080p30，那gop设置为30/60/90
从上面可以看到，由于输入相机帧率不确定，所以我们一般建议配置0(Auto)
cvbs分制式，pal是25fps，ntsc是30fps
假设是pal，那gop设置25/50/75
1、大的I帧容易因为无线传输的原因导致丢帧花屏；
2、gop设置大，I帧丢失导致花屏后恢复时间变长；
3、I帧和P帧大小差别大，会增加传输延迟
Vennligst last ned på lenken nedenfor.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
- We can modify the TS stream over UDP, but the TS stream is a non-standard TS stream that we have modified, which needs to be interpreted by our decoder board or special player (nedlasting).
- If you agree with the RTSP protocol, VLC can play it; if you only agree with the TS stream (due to our non-standard modification), VLC cannot decode and play it, so we must use our special player. (nedlasting).
- If you want to switch to the standard MPEG-2 TS stream to play with VLC, our software engineer can customize the firmware for you (this will take a few days) for an additional fee of USD500.
- We use non-standard mpeg-2 ts streams primarily for the following reasons:
- The standard mpeg-2 ts stream has too much overhead outside the effective data, making it unsuitable for use with cofdm;
- The standard mpeg-2 ts stream is difficult to implement the aes encryption function;
- The standard mpeg-2 ts stream is difficult to achieve serial port transparent transmission (used with our decoder board)
- If you don't need our decoder board, encryption and serial port transparent transmission, it is also possible to use standard mpeg-2 ts stream
- It is recommended that you try our player; in real-time performance, our player outperforms vlc.
The vlc player's algorithm does not take into account real-time performance; i stedet, it will constantly adjust its cache (only increase but not shrink). Som et resultat, the longer it is played, the longer the delay may be (especially when used with a wireless link)
1. SSL certificate is HTTPS protocol, our products do not support it now, only HTTP.
2. The default encoder board through the RTSP protocol, RTSP is not encrypted. You can set a longer password. And change it frequently.
3. If you want to encrypt, you need to use a pair of our codec boards (with encoder and decoder board as TX and RX), with UDP protocol, and they are using aes256 encryption. (Just like the bank level.)
Ja, Sikker, værsåsnill kontakt oss. Let me list your demand at the below.
1. We need to take a composite analog PAL video signal and transmit it using h264 over MPEG2 TS. OK
2. The output must be playable through VLC. OK
3. UPD://@1030. OK
4. The output network stream packet should be 188 bytes standard mpeg2 TS. OK
5. Compression scheme is h. 264, CVBS PAL input and IP output. OK
Sikker
Vennligst sjekk lenken nedenfor
COFDM UART AT command for the transmitter and Receiver.
Eller
Download the COFDM Transmitter UART AT command PDF.
Please follow the checkpoints below to confirm.
- After connecting the encoder board with your computer by ethernet cable, the LED of RJ45 connector should be blinking or not. (to check the ethernet connection is ok or not)
- Is your computer configured with 192.168.1.x network segment ip?
- Have you modified the default IP address of the encoding board? If the IP address changed, maybe you can download and use the below software to find what IP address now.
- Or Directly connect the UART cable of the encoding board to the computer, and use the serial port debugging assistant to send the ATGIP_ command.get ip address command Operation Video at Youtube
Format
ATGIP_
Eksempel: ATGIP_
Parameter
Nei
Bruk
to query the current IP address of the receiving end
Returverdi
Eksempel:
ATGIP_
ATGIP192.168.0.215 OK
Bemerke
- query command
- More COFDM UART AT commands, please check this link. https://ivcan.com/encoder-modulator-decoder-demodulator-module-parameter/
These parameters are determined by the camera, only the sensor has it.
One more question: In the future is there any possibility to incorporate these features in the output side of encoder (if we get volume orders) ?
Our Answer: These are the parameters of the isp, and our current encoding boards are all bypass isp (because we don't connect the sensor, we don't need and can't use the isp), so we can't add these parameters.
Ja, CVBS input support NTSC and PAL, Automatic detection and adaptation
- De parameter configuration board tool is mainly used for the COFDM module function. If you buy this HDMI / CVBS to IP encoder Vcan1746 separately, you don’t need to buy a parameter configuration board tool, you can adjust the parameters through the Web UI.
- Selvfølgelig, if you want to use the parameter configuration board tool to adjust some parameters of the encoder board, it is also possible.
- For eksempel, the video encoding bit rate can be configured through the Web UI or changed through the extra parameter configuration board tool. The Web UI can configure all the parameters, and the parameter configuration board tool can only adjust some of them.
Ok, vennligst sjekk lenken nedenfor
Ja, hvis du trenger, we can offer you the special firmware to have USB recorder function.
Spørsmål: Does your USB DVR support playback on the encoded video?
Svar: Nei, The USB has the record function. You need to play it on a computer, it can not playback on the encoder board directly.
- Do you mean HDMI or AV input, or do you need HDMI and AV to support two simultaneous inputs?
- Currently it supports either HDMI or AV input.
-
Vcan1746 can only choose one of HDMI/AV at present, other boards can meet the firmware you need, but this board only supports SDI + AV/AHD output.
-
If necessary, you can evaluate the board with SDI + AV/AHD input to see if it meets your requirements. Hvis ja, our HDMI + AV input Vcan1746 can be made the same later.
-
If you really need to evaluate the HDMI + AV-grensesnitt, please first buy Vcan746 and burn the default shipping firmware for testing. HDMI and AV can be selected for use. If there is a certain amount of follow-up orders, we can develop a special firmware to support HDMI+AV input at the same time.
-
The display of HDMI and CVBS video input by two channels at the same time is similar to Hikvision IPC, which is divided into main bit rate and sub bit stream. The main stream corresponds to HDMI, and the sub stream corresponds to CVBS.
- Now we can develop a new firmware to support HDMI and CVBS to live streaming at the same time, but the audio can only be selected from one of the two (the system selects HDMI audio/analog audio according to the video access situation).
Supported.
Our HDMI and CVBS input video encoding board has a USB interface, which can be used for USB recording. It can also be used as the input interface of a USB web camera.
På denne måten, our video encoding board can convert the signal of your USB web camera into a network interface, while supporting ultra-low latency and supporting h264 and h265 encoding.
HDMI Video Sources Input IP Ethernet Output encoder, VLC RTSP operation
Industrial-grade temperature range from -40°C to 70°C Celsius test
Support HDMI and CVBS 2 video streams at the same time
How to get the IP address of the encoder back if you forget
More FAQ
HS Code
8517629900, Some of our customers use this HS code for your reference.
Special Function Custom Development
-
HDMI and CVBS Dual Video Encoding
-
USB has a video recording function.
-
Special handling of encoding formats to match your custom decoder board
скачать видеокодер
