Wireless broadband SDR ad hoc network module
വയർലെസ് ബ്രോഡ്ബാൻഡ് SDR അഡ്ഹോക്ക് നെറ്റ്വർക്ക് മൊഡ്യൂൾ ടു-വേ വീഡിയോ, ശബ്ദം, ഡാറ്റ സുതാര്യമായ കൈമാറ്റം
ഉള്ളടക്ക പട്ടിക
നേട്ടം
① Ad hoc radio frequency 1
② Ad hoc radio frequency 2
③ DC 12V input/network port
④ RS232/voice (തിരഞ്ഞെടുക്കുക 1 നിന്ന് 2)
⑤ Power switch
⑥ GPS Beidou/WIFI (തിരഞ്ഞെടുക്കുക 1 നിന്ന് 2)
⑦ Power Indicator
⑧ Ad hoc network indicator
സവിശേഷതകൾ
- No center anti-destroy network structure: The departure or damage of any node does not affect the operation of the overall network
- Multiple business data: Support video, ശബ്ദം, location, sensor, and other IP-based data transmission
- Multiple access methods: Support Ethernet port, and serial port, can support the transmission of control commands and video data at the same time
- Strong anti-interference ability: Support automatic spectrum migration and frequency hopping working mode
- കോംപാക്റ്റ് വലുപ്പം: Size 133×66×33mm; Weight 400g
വിവരണം
Package Include
(1). One ad hoc network host
(2). 2 dedicated frequency band (1.4GHz) ആന്റിനകൾ (depending on different models, other types of antennas are optional)
(3). Common frequency band (2.4Ghz/GPS Beidou) ഏരിയെല് (തിരഞ്ഞെടുക്കുക 1 നിന്ന് 2)
(4). Power supply/network port conversion cable 1 കഷണം
(5). Voice/RS232 transfer cable 1 (തിരഞ്ഞെടുക്കുക 1 നിന്ന് 2)
(6). DC 12V adapter 1pc
Installation steps
1. Install the antenna: connect the dedicated frequency band antenna (or feeder) to the TNC head (RF1/RF2), press and rotate to fix it, and ensure that the antenna is tightened and not loose;
2. Install the power supply/network port conversion cable: connect the aviation plug (2 cores) to the main engine aviation seat, and then tighten the nut to ensure good contact.
Boot steps
- Press the switch, turn on the power, the indicator light of the power switch is on, and the system starts self-test (It is forbidden to turn on the power without connecting the antenna, and it is forbidden to use other types of adapters)
- After the self-inspection is completed after the neighbor node is found, the self-organizing network indicator is always on, indicating that the network is successfully established
Networking
The networking indicator light indicates the status of being in the network or being disconnected from the network. When the indicator light is on, it indicates that the network has been established. Green indicates that the network quality with neighboring nodes is good, orange indicates normal, and red indicates poor quality.
സീരിയൽ നമ്പർ | state | meaning |
1 | light off | offline |
2 | green steady | good network quality |
3 | Orange is always on | Average network quality |
4 | Steady red | poor network quality |
Precautions
- ആൻ്റിന കർശനമാക്കിയിട്ടുണ്ടെന്ന് ഉറപ്പാക്കുക;
- ടെസ്റ്റ് സമയത്ത് ആൻ്റിന നിലത്തു ലംബമായി വയ്ക്കുക;
- പരിശോധനയ്ക്കിടെ നിങ്ങളുടെ കൈകളോ മറ്റ് വസ്തുക്കളോ ഉപയോഗിച്ച് ആൻ്റിനയിൽ തൊടരുത്;
- ഉപകരണങ്ങൾക്കിടയിൽ പരസ്പരം കൂടുതൽ അടുക്കുന്നത് അഭികാമ്യമല്ല, അവ 5M-ൽ കൂടുതൽ വേർതിരിക്കേണ്ടതാണ്;
- ടെസ്റ്റ് വ്യവസ്ഥകൾ ഉണ്ടെങ്കിൽ, നോഡുകളിലൊന്ന് സ്ഥാപിക്കാൻ ഒരു കമാൻഡിംഗ് ഉയരം തിരഞ്ഞെടുക്കുക;
- നെറ്റ്വർക്ക് ഇൻഡിക്കേറ്റർ ലൈറ്റിലൂടെ ആശയവിനിമയ ലിങ്ക് സാധാരണമാണോയെന്ന് പരിശോധിക്കുക, നെറ്റ്വർക്ക് ഇൻഡിക്കേറ്റർ ലൈറ്റ് എപ്പോഴും ഓണാണ്, indicating that the link layer has been successfully connected;
- Check the environmental noise situation through the WEB interface to know whether there is co-channel interference around;
- കുറിച്ച് 5 seconds after the networking is successful, you can check the network connectivity of each node through the ping packet;
- Make sure that the cameras, PCs, and other devices that need to be connected are in the same IP address segment, and can communicate normally under the condition of a wired connection, without using the same address segment of NexFi devices (NexFi devices communicate through MAC addresses);
- Traffic flow, people flow, കെട്ടിടങ്ങൾ, and trees will have varying degrees of impact on communication quality;
- When doing penetration tests inside and outside the building, the external nodes should not be too close to the building, ദൂരം 10M-ൽ കൂടുതലായിരിക്കണം;
- നിങ്ങൾക്ക് കൂടുതൽ ടെസ്റ്റ് ദൂരം നേടണമെങ്കിൽ, you can adjust the bandwidth to 5Mhz through the management interface, നിങ്ങൾക്ക് ഒരു വലിയ ബാൻഡ്വിഡ്ത്ത് നേടണമെങ്കിൽ, നിങ്ങൾക്ക് ഇത് 20Mhz ആയി ക്രമീകരിക്കാം;
- വീഡിയോ ട്രാൻസ്മിഷനാണ് ഉപയോഗിക്കുന്നതെങ്കിൽ, വീഡിയോ ഫ്രീസ് ചെയ്യാതിരിക്കാൻ, ക്യാമറ റെസല്യൂഷൻ ക്രമീകരിച്ചുകൊണ്ട് നിങ്ങൾക്ക് വീഡിയോ ഇഫക്റ്റ് ഒപ്റ്റിമൈസ് ചെയ്യാം, ഫ്രെയിം റേറ്റ്, ട്രാൻസ്കോഡിംഗ് സ്ട്രീം, മറ്റ് പരാമീറ്ററുകളും;
- If it is used for open-air day and night testing, ദയവായി വാട്ടർപ്രൂഫ് നടപടികൾ കൈക്കൊള്ളുകയും നല്ല താപ വിസർജ്ജനം സമ്പർക്കം ഉറപ്പാക്കുകയും ചെയ്യുക.