SNM401 Ad Hoc Network Module
ഉള്ളടക്ക പട്ടിക
1. ഉൽപ്പന്ന വിവരണം
SNM401 Centerless Ad Hoc Network Module realizes centerless long-distance communication between modules, and adopts the world’s latest LDPC encoding and decoding technology, compared to the RS level used by traditional radio stations The concatenated convolutional code can have a coding gain of 5dB, and at the same time, through the “self-relay wireless communication” സാങ്കേതികവിദ്യ, it innovatively realizes automatic relay between modules, thereby greatly improving the coverage effect and transmission distance. SNM401 adopts ad-hoc network wireless communication technology, any node can receive and process the same signal forwarded by multiple nodes at the same time, combine these signals forwarded from different nodes, demodulate the original information to the greatest extent possible, and have a larger transmission distance and higher transmission reliability. The wireless communication technology of the ad hoc network does not require routing, and multiple nodes automatically determine whether to start the forwarding according to the received signal quality and field strength, and the relay is upgraded from a multi-hop single-point relay to a multi-hop multi-point relay. The state relay is upgraded to a mesh relay. When any node in the relay network is disconnected from the network, other relay lines in the relay network work normally so that the relay effect is not affected.
2. ഉൽപ്പന്ന സവിശേഷതകൾ
◆Operating frequency: 400-500മെഗാഹെട്സ്
◆Single-hop transmission distance: 3~5Km
◆Dynamic topology convergence: 1മിസ്
◆Transmit power: 1പ
◆Receive sensitivity: -127dBm
◆Working voltage: 3.5-4.5വി
◆Signal to noise ratio Threshold: 1dB
◆Channel spacing: 12.5ഹേർട്സ്
◆Frequency stability: 1പിപിഎം
◆Intermodulation: 65dB
◆Encryption: 256എഇഎസ്
◆Spurious response immunity: 75dB
◆Adjacent channel selectivity: 65[email protected]
◆Operating temperature: -40~ +85℃
◆Module size: 33.5X42X3.4mm
3. അപേക്ഷ
◆Internet of Things ◆Individual Soldier System ◆Emergency Broadcasting
◆UAV ◆Real-time Remote Control ◆Digital Intercom
◆Emergency Communication ◆Robot ◆Wireless Data Transmission
4. Working Parameters
Table 1: Operating Parameters Table
പാരാമീറ്റർ | വ്യവസ്ഥകൾ | ഏറ്റവും കുറഞ്ഞ | മാതൃകയായ | പരമാവധി | ഘടകം |
Operating Frequency Band | 400 | 500 | മെഗാഹെട്സ് | ||
ഓപ്പറേറ്റിങ് താപനില | -40 | 25 | +85 | ℃ | |
പ്രവർത്തിക്കുന്ന വോൾട്ടളവ് | 3.5 | 4 | 4.5 | വി | |
Transmitting Power | 30 | dBm | |||
സെൻസിറ്റിവിറ്റി സ്വീകരിക്കുന്നു | -130 | -127 | -125 | dBm | |
Maximum RF Input Power | +33 | dBm | |||
സീരിയൽ പോർട്ട് ബാഡ് നിരക്ക് | 115200 | bps | |||
sleep current | @ EN=0 | 40 | uA | ||
കറൻ്റ് സ്വീകരിക്കുക | 160 | mA | |||
transmit instantaneous current | @VCC==4V, 1പ | 1800 | mA | ||
transmit average current | @VCC==4V, 1പ | 600 | mA | ||
audio input voltage | 1.5 | വി.പി.പി | |||
audio output Impedance | 150 | ഓം |
കുറിപ്പ്: മൊഡ്യൂളിൻ്റെ പ്രവർത്തന സാഹചര്യങ്ങൾ മുകളിലുള്ള പരിധി മൂല്യങ്ങൾ കവിയുന്നുവെങ്കിൽ, ഇത് മൊഡ്യൂളിന് സ്ഥിരമായ കേടുപാടുകൾ വരുത്തിയേക്കാം.
5. Module pins and definitions
ചിത്രം 1 SNM401 Pin Diagram
Abbreviation | വിവരണം |
AI | Analog input |
AO | Analog output |
AIO | Analog bi-direction |
DI | ഡിജിറ്റൽ ഇൻപുട്ട് |
DO | ഡിജിറ്റൽ ഔട്ട്പുട്ട് |
DIO | Digital bi-direction |
പി | ശക്തി |
ജി | ഗ്രൗണ്ട് |
Table 3 SNM401 pin definition
പിൻ നമ്പർ | പിൻ നാമം | ടൈപ്പ് ചെയ്യുക | വിവരണം |
1 | നഗരത്തിലേക്കുള്ള | ജി | നഗരത്തിലേക്കുള്ള |
2 | ഉറുന്വ് | AIO | antenna port |
3 | നഗരത്തിലേക്കുള്ള | ജി | നഗരത്തിലേക്കുള്ള |
4 | നഗരത്തിലേക്കുള്ള | ജി | നഗരത്തിലേക്കുള്ള |
5 | VBAT | പി | External 3.5V-4.5V battery or power supply, 4V is recommended |
6 | VBAT | പി | |
7 | നഗരത്തിലേക്കുള്ള | ജി | നഗരത്തിലേക്കുള്ള |
8 | നഗരത്തിലേക്കുള്ള | ജി | നഗരത്തിലേക്കുള്ള |
9 | TX_STATE | DO | module transmit indication Signal, the high level is transmitting |
10 | RX_STATE | DO | module receiving indication signal, the high level is receiving |
11 | എൻ.സി | No connect | |
12 | എൻ.സി | No connect | |
13 | നഗരത്തിലേക്കുള്ള | ജി | നഗരത്തിലേക്കുള്ള |
14 | TXD | DO | serial port data transmitting pin |
15 | RXD | DI | serial port data receiving pin |
16 | SET | DI | module Serial port configuration signal, configure parameters when high level, send and receive data when low level |
17 | EN | DI | module open enable signal, high level open, low level close |
18 | നഗരത്തിലേക്കുള്ള | ജി | നഗരത്തിലേക്കുള്ള |
19 | PRO1 | DIO | programmable definition pin |
20 | PRO2 | DIO | programmable Definition pin |
: The module is regulated by 3.3V LDO inside, and all digital IOs are 3.3V level.
6. പാക്കേജ് വലുപ്പം
ചിത്രം 2 SNM401 size chart
ചിത്രം 3 SNM401 package Figure
7. LAYOUT precautions
1.ദിSNM401 module works at 400-500മെഗാഹെട്സ്and the influence of various factors on wireless transceivers should be avoided.
- It is laid under the module നഗരത്തിലേക്കുള്ള, and the traces are extended to the periphery as far as possible.
- It is recommended to use insulating material to isolate the module mounting position on the substrate, ഉദാഹരണത്തിന്, place a whole piece of in this position
silkscreen
- Try to take a short and thick power line to the module, the recommended copper line width is80mil, and the decoupling capacitor should be placed as close to the power pin as possible.
8. Software configuration
8.1 Parameter configuration
Users can obtain and configure parameters through the serial port, the serial port baud rate ആകുന്നു 115200, the data bit is 8ബിറ്റ്, the stop bit is 1ബിറ്റ്, and there is no parity bit.
Table 4 Serial port packet format
Serial port table packet | |||
identification word | നീളം | Command | instruction reply/reply content |
1Byte | 1Byte | 1Byte | NByte |
8.1.1 Identification word
The identification word is fixed as 0x68.
8.1.2 നീളം
നീളം COFDM വയർലെസ് ട്രാൻസ്മിഷൻ സിസ്റ്റം ട്രാൻസ്മിഷൻ നിരക്ക് കണക്കുകൂട്ടൽ command + command content/reply content.
8.1.3 Command
PAL/NTSC ഓട്ടോമാറ്റിക് പരിവർത്തനം 5 Serial Command-List
ഫംഗ്ഷൻ | Command | ഉള്ളടക്കം | Reply Content |
Acquire RF Parameters | 0x00 | ഇല്ല | ഫ്രീക്വൻസി(4Byte) +ശക്തി(1Byte) +കോൺഫിഗറേഷൻ
Status(1Byte) +Noise(2Byte) +Baseband Version Number(1Byte) |
Set RF Parameter | 0x01 | ഫ്രീക്വൻസി(4Byte) +ശക്തി(1Byte) | ഇല്ല |
data relay level | 0x0C | ഇല്ല | data relay level(1Byte) |
Set data relay level | 0x0D | Data relay level(1Byte) | ഇല്ല |
key to acquire | 0x0E | ഇല്ല | key(32Byte) |
set key | 0x0F | key(32Byte) | ഇല്ല |
get module version | 0x12 | ഇല്ല | module name + version number |
module ready | 0x55 | ഇല്ല | ഇല്ല |
save configuration | 0x66 | ഇല്ല | ഇല്ല |
data receive | 0xA2 | ഇല്ല | transparent data (NByte) |
data send | 0xB2 | transparent data (NByte) | ഇല്ല |
8.1.4 Instruction content/reply content
8.1.4.1 Obtaining RF parameters
ഫ്രീക്വൻസി: The unit is ഹെര്ട്സ്, the setting range is ~5000000000, and the precision is 500HHz.
ശക്തി:1-high power 1പ,0-കുറഞ്ഞ ശക്തി 0.5പ, the default is high power 1പ.
Configuration status: Indicates the radio configuration status,0-uninitialized,1-configuring,2-configured successfully.
Noise Floor: Indicates the current frequency noise intensity, ഏത് 2 is meaningful
Baseband version number: The upper 4 bits represent the major version number, and the lower 4 bits represent the minor version number.
Configuration Packet:0x68 0x01 0x00
Return Packet:0x68 0x0A 0x00 Frequency Power Configuration Status Noise Floor Baseband Version No.
8.1.4.2 Setting RF Parameters
After configuring RF parameters, you must wait for the successful configuration (കുറിച്ച് 2 സെക്കൻഡ്) before the module can enter the setting work correctly state.
Configuration package:0x68 0x06 0x01 Frequency power
return package:0x68 0x01 0x01
8.1.4.3 Obtaining data relay level
SH ad hoc network technology is a simulcast mesh relay method, which does not require routing, which can greatly improve the coverage.number of relay hops എൻ refers to the number of hops that can be relayed during data transmission, and the maximum number of relay hops is 16. With each additional hop, the transmission distance doubles, but the transmission time increases accordingly, as shown in the table below.
Table 6 Comparison of Relay Levels
Relay Hops | Transmission Bytes | Transmission Time |
എൻ | <36 | N*50ms |
എൻ | 37-72 | N*100ms |
എൻ | 73-108 | N*150ms |
എൻ | 109-144 | *200മിസ് |
എൻ | 145-180 | N*250ms |
എൻ | 181-216 | N*300ms |
എൻ | 217-252 | N*350ms |
എൻ | 253-288 | N*400ms |
Configuration package: 0x68 0x01 0x0C
Return package: 0x68 0x02 0x0C Data relay level
8.1.4.4 Set data relay level
Configuration package:0x68 0x02 0x0D Data relay level
return packet:0x68 0x01 0x0D
8.1.4.5 Obtain the key
key for communication encryption, the module will automatically discard the voice information and data information whose key is inconsistent with its own key, and the key is all 0.
Configuration Packet:0x68 0x01 0x0E
Return Packet:0x68 0x21 0x0E കീ
8.1.4.6 Set Key
Configuration Packet:0x68 0x21 0x0F കീ
Return Packet:0x68 0x01 0x0F
8.1.4.7 Get Module Version
Configuration Packet:0x68 0x01 0x12
Return Packet:0x68 0x15 0x12 0x53 0x69 0x6d 0x75 0x6c 0x48 0x6f 0x63 0x32 0x31 0x38 0x5f 0x31 0x31 0x30 0x2e 0x30 0x00 ആകുന്നു“Simulhoc2618_V1.0.0”
8.1.4.8 മൊഡ്യൂൾ
Return package:0x68 0x01 0x55
8.1.4.9 Save configuration
command to save all settings to ഫ്ലാഷ്, and the saved configuration will be used directly after power-on.
Configuration package:0x68 0x01 0x66
Return package:0x68 0x01 0x66
8.1.4.10 Data reception
When the SET pin is low, the module will transparently transmit the received data package to the user. The length varies according to the actual transparent transmission data length.
Return package:0x68 നീളം 0xA2 Transparent
8.1.4.11 Data transmission
Only when the SET pin is at a low level can data be transmitted, and the data sent in a single transmission does not exceed 36 ബൈറ്റ്. The length varies according to the actual transparent transmission data length. If a return packet is received, it indicates that the data transmission failed this time.
Configuration package: 0x68 Length 0xB2 Transparent data
return package: 0x68 0x01 0xB