2 Watts 5 Watts 10 Watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
$450.00 – $980.00
2 Vött eða 5 Vött eða 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
Þetta er lykilatriði í þráðlausum myndsendi, sem getur stækkað RF merkið fyrir lengri svið og fjarlægð. valfrjálst 1 Watt, 2 Watt, 5 Watt, og 10 Watt.
Efnisyfirlit
Features
- Tíðnisvið: 800Mhz-830Mhz, 1425MHz-1455MH
- RF inn: 25± 2dBm
- RF út afl: 2 Watt (33dBm)
- 1400Mhz Transmitter gains 11dB when used with tvíhliða þráðlaus myndbandsgagnatengingareining, stilltu hámarks RF afl sem 22~24 dBm, then the RF out power will be 33~35 dBm.
- 800Mhz sendistyrkur: 13dB, when used with a two-way wireless video data link module, stilltu hámarks RF afl sem 20~22 dBm, then the RF out power will be 33~35 dBm.
- RF út afl: 5 Watt (37dBm)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, stilltu hámarks RF afl sem 22~25 dBm, then the RF out power will be 37~37 dBm.
- 800Mhz sendistyrkur: 17dB, when used with a two-way wireless video data link module, stilltu hámarks RF afl sem 20~22 dBm, then the RF out power will be 37~39 dBm.
- RF út afl: 10 Watt (40dBm)
- TX fá: 18dB, when used with a two-way wireless video data link module, stilltu hámarks RF afl sem 22~24 dBm, þá verður RF út krafturinn 40~42dbm.
- 2 Vött afl í DC12V~16V;
- 5 Vött afl í DC24V~25V, lágmark 1,8A@24V aflstraumsmat
- 10 Vött afl í DC24V~30V, lágmark 2,5A@28V aflstraumsmat
- 2 Vött Orkunotkun: <6W Meðal; 5 Vött Orkunotkun: <14W Meðal; 10 Vött Orkunotkun: <28W meðaltal
- 2 Watts 5 Wött PCBA stærð: 46.5*31mm, þykkt PCB: 1.2mm
- 10 Watt Stærðir: 65*62*13.5mm, ekki með tengið út úr málmhúsinu, þyngd: 98g
- viðnám: 50 óm
Vinna saman við tvíhliða þráðlaus myndbandsgagnatengileining:
RF Input
RF úttak
| • Modular hönnun og mikil samþætting | We should solder two bonding pads to connect with power VDD and GND. |
| stjórn | We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL og GND). Inntakið hátt (1.8V til 3,3V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode. |
| RF inn | IPEX tengi fyrir tengingu við aðalloftnet tvíhliða þráðlausu myndbandsgagnatengingareiningarinnar. |
| RF út | We should solder the bonding pad to an antenna connector. |
Húsnæði og setja saman
We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.
To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.
It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.
Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.
Við getum líka búið til málmhólf fyrir þessa PA-einingu í samræmi við kröfur viðskiptavinarins.
Líkanið hér að neðan er með innbyggðum kraftmagnara að innan.
FAQ:
Q: Could you tell me your RF power amplifier dimension size? I want to design my enclosure.
A: Vinsamlegast athugaðu hér að neðan mynd. And tell us if you need any further information.
Q: Could you show me the real photos of your RF linear power amplifier?
A: sure, please check the below pictures.
Q: Are you not using the TQP7M9104 amplifier in the 2W module?
A: engin
